Air King 7000 Installations- und Betriebsanleitung

Blättern Sie online oder laden Sie pdf Installations- und Betriebsanleitung für Befeuchten Air King 7000 herunter. Air King 7000 10 Seiten. Air king model 7000 flow through humidifier

Seite drucken

kitchensource.com

• READ THESE INSTRUCTIONS FULLY BEFORE INSTALLING

THIS PRODUCT.

• SAVE THESE INSTRUCTIONS FOR REFERENCE.

• WHEN DRILLING OR CUTTING INTO DUCTING BE

EXTREMELY

CAREFUL

CONDITIONING COILS OR OTHER FURNACE APPARATUS.

• THIS UNIT MUST BE INSTALLED IN 10" WIDE DUCT

MINIMUM.

• FOR THIS UNIT TO OPERATE PROPERLY YOUR FURNACE

SHOULD ACHIEVE A HEATING TEMPERATURE OF AT LEAST

35'C (95'F) IN ONE MINUTE. IF IT DOES NOT YOU MAY

HAVE TO PURCHASE A SECONDARY ACTIVATION SWITCH

(SOLD SEPARATELY).

• DO NOT INSTALL THIS UNIT WHERE EXTREME

TEMPERATURES EXIST (BELOW 8'C / 45'F OR ABOVE 63'C /

145'F).

• THIS UNIT REQUIRES A DRAIN TO ALLOW WATER TO

FREELY RUN OFF.

• FOR THIS UNIT TO OPERATE PROPERLY IT MUST BE

INSTALLED ON A FORCED AIR HEATING SYSTEM WITH A

SUPPLY DUCT AND RETURN DUCT.

• THE HUMIDIFIER BODY AND THE BYPASS COLLAR DAMPER

ARE TO BE INSTALLED ON DUCTING ONLY. UNDER NO

CIRCUMSTANCES MOUNT ANY COMPONENT TO THE

FURNACE BODY.

• ELECTRICAL WIRING, WATER SUPPLY, AND DRAIN TUBE

MUST NOT KINK OR COME INTO CONTACT WITH SHARP

EDGES OR HOT SURFACES.

• IF REPLACING AN EXISTING FURNACE HUMIDIFIER, WE

RECOMMEND YOU REPLACE ALL COMPONENTS TO

ENSURE PROPER HUMIDIFIER OPERATION.

• THE INSTALLATION OF THIS PRODUCT MUST COMPLY

WITH NATIONAL AND LOCAL ELECTRICAL, PLUMBING,

BUILDING, AND MECHANICAL CODES.

REQUIRED TOOLS

• Safety glasses

• Work gloves

• Electric or cordless drill

• Drill bits (3/8", 1/8", 7/32", 7/64")

• Tin snips

• Full size Philips or Roberstons screw driver

• Short handle Philips or Roberstons screw driver

• Adjustable wrench

• Utility knife

• Pliers

• Level

• Measuring tape or ruler

• Medium-grit sand paper

• Pencil

Call 1-800-667-8721 anywhere in the US and Canada

Model 7000 Flow Through Humidifier

INSTALLATION AND OPERATING INSTRUCTIONS:

MODEL 7000 FLOW THROUGH HUMIDIFIER

NOT

DAMAGE

SELECTION OF LOCATION

TO MOUNT THE HUMIDIFIER

All bypass type furnace mount humidifiers rely on the pressure

difference which exists between the supply duct (hot air) and the

AIR-

return duct (cold air) to create an air flow through the

humidifier's evaporator pad. The air will ALWAYS flow from Hot

(high pressure) to Cold (low pressure).

Selecting the proper location and installing the humidifier

properly as intended by the manufacturer is imperative for the

proper operation of the humidifier. See illustrations below along

with the brief explanations as to what a good installation is and

what is not.

•INSTALLATION TIP: Before starting fully plan out the

installation. Check for the locations of the humidifier,

bypass collar & damper, and the humidistat and

associated sensors. Plan the length and type of ducting

required, the water supply, the water drain, the electrical

wiring, and a constant 120 volt outlet to plug in the

transformer. This will ensure your installation goes as

easy and quickly as possible

IDEAL INSTALLATION

Figure 1

SUPPLY DUCT

Damper fully open

1. The humidifier body and bypass tube are installed at eye level,

easily accessible for installation and routine maintenance.

2. The space between the humidifier body and bypass tube are no

more than 30" to ensure maximum air flow through the humidifier.

3. The supplied aluminum flex bypass tube are cut to the proper

length and pulled tight to ensure maximum air flow.

4. The bypass damper is fully open.

5. The humidifier is mounted level on the duct.

6. There is nothing inside the duct behind the bypass collar &

damper or the humidifier body.

7. The humidifier and bypass collar and damper are level.

kitchensource.com

RETURN DUCT

COLD AIR

WARM AIR

No more

than 30"

10" wide duct minimum

Bypass collar and

unit level

Bypass tube pulled

tight and cut to length

Water flowing to drain