Air King 7000 Installations- und Betriebsanleitung - Seite 6

Blättern Sie online oder laden Sie pdf Installations- und Betriebsanleitung für Befeuchten Air King 7000 herunter. Air King 7000 10 Seiten. Air king model 7000 flow through humidifier

Seite drucken

Model 7000 Flow Through Humidifier

selecting a location to mount the humidistat keep in mind the

following.

• The humidistat should be at least 6" above the humidifier body.

To ensure humidified air being introduced into the duct is not

being sensed.

• The humidistat should always be mounted on the return duct

(cold air). This will ensure that the air from the living area is being

sensed.

• Try to avoid areas where fresh air is being introduced into the

return duct. This will cause false readings. It will always be better

to locate the humidistat up stream from any Fresh Air intake.

• The humidistat comes with 3 feet of cable for connection to the

humidifier. If your installation requires a longer cable, a 10 foot

length of cable can be purchased through our Parts & Service Line,

Part Number 011175001.

The humidistat comes packaged from the factory fully assembly

along with the cable for power connection to the humidifier, the

outdoor air sensor (for use in automatic mode only), and 2

humidistat labels, one if the humidistat is in manual mode and

other for automatic mode. To install the humidistat you will first

have to disassemble it.

humidistat knob, to remove the front cover use a slot screw driver

and insert the end into the opening in the humidistat housing as

shown. This will expose the Control Base and board. You may

now mount the control in the selected location.

Figure 20

1. Affix the humidistat mounting template to the duct using tape.

(Combination template with the humidifier body template.)

2. Drill the 4 marked mounting holes

3. Drill a 3/8" hole inside the rectangle marked Humidistat Cut

Out.

4. Using the 3/8" hole as a starting point cut out the Humidistat Cut

Out using tin snips (not supplied.

5. Mount the humidistat control to the duct using the 4 screws

packaged with the humidistat.

6. Connect the control cable to the humidistat (fig 21.)

7. Connect the other end of the control cable to the humidifier side

panel. (fig 22)

HUMIDISTAT CONTROL–SETTING AUTOMATIC OR MANUAL OPERATION.

You have an option of selecting one of two operation modes for

your humidistat. There is a switch on the side of the humidistat

for setting Automatic or Manual – With the Switch in the UP

position the humidistat is in Manual, if the switch is in the

Referring to figure 20, remove the

Figure 21

DOWN position the control is in

Automatic. Also provided are two humidistat labels, one for

Automatic (Fig 23) and one for Manual (Fig 24)

Manual Humidistat Operation. (Switch UP) – With the control

set up for manual operation it will work the same as a normal

Figure 23

Figure 24

the humidistat front cover, position the manual humidistat label,

and replace the knob.

Automatic Humidistat Operation. (Switch DOWN) – With the

control set up for automatic operation the control will

automatically adjust the humidity set point based on outdoor air

temperatures. The purpose of this feature is to protect against

over humidification and condensation problems. Referring to the

chart below (fig 25) the control will achieve no higher humidity

levels than that shown for corresponding outdoor air temperature

and dial setting. An example is shown, with the control set at 5

and an outdoor air temperature of 0'C/30'F the maximum

humidity level achieved will be 40%. The humidity levels used

in automatic mode are based on ASHRAE standards to protect

against over humidification.

humidistat in automatic mode you will have to install the outdoor

Figure 25

outside window where a representative outdoor air temperature

Figure 22

humidistat.

DO NOT use or

connect

outdoor air sensor

and you will have

to set the desire

Automatic Mode

humidity level and

make all necessary

a d j u s t m e n t s

manually.

select to operate

the humidistat in

manual operation

no further set up is

Manual Mode

required. Replace

If you select to operate the

air temperature sensor.

The sensor plugs into the

control board next to the

main cable (fig 26). The

other end of the sensor

wire ideally should be

placed outside and held in

place

via

(supplied)

holding

sensor head (fig 27). If you

are unable to get the

sensor

outside

acceptable to place the

sensor on the surface of an

You

the

If you

screw

the