Bosch DISHWASHER Betriebsanweisungen - Seite 21

Blättern Sie online oder laden Sie pdf Betriebsanweisungen für Geschirrspüler Bosch DISHWASHER herunter. Bosch DISHWASHER 24 Seiten. Dishwasher bosch
Auch für Bosch DISHWASHER: Gebrauchsanweisung Handbuch (30 seiten), Installationsanleitung Handbuch (34 seiten), Betriebsanleitung (30 seiten), Betriebsanleitung (28 seiten), Betriebsanleitung (30 seiten), Betriebsanleitung (38 seiten), Betriebsanleitung (42 seiten), Gebrauchsanweisung Handbuch (32 seiten), Gebrauchsanweisung Handbuch (36 seiten), Gebrauchsanweisung Handbuch (30 seiten), Betriebsanleitung (24 seiten), Gebrauchsanweisung Handbuch (26 seiten), Gebrauchsanweisung Handbuch (40 seiten), Gebrauchsanweisung Handbuch (28 seiten), Gebrauchsanweisung Handbuch (29 seiten), Betriebsanleitung (28 seiten), Betriebsanleitung (28 seiten), Gebrauchsanweisung Handbuch (28 seiten), Installationsanleitung Handbuch (50 seiten), Installationsanleitung Handbuch (20 seiten), Gebrauchsanweisung (36 seiten), Betriebsanleitung (25 seiten), Betriebsanleitung (46 seiten), Gebrauchsanweisung Handbuch (31 seiten)

Seite drucken
Bosch DISHWASHER Betriebsanweisungen

Installation

The required installation dimensions can
be found in the installation instructions.
Level the appliance with the aid of the
height-adjustable feet. Ensure that the
appliance is situated securely on the floor.
– A built-under or integrated appliance
which is installed subsequently as a
free-standing appliance must be
secured to prevent it from overturning,
e.g. by screwing it to the wall or by
installing it under a continuous worktop
which is screwed to adjacent
cupboards.
– The appliance can easily be
installed in a fitted kitchen between
wooden and plastic walls.

Waste-water connection

– The required work sequence can be
found in the installation instructions. If
required, fit a siphon with an drainage
connection.
– Connect the waste-water hose to the
drainage connection of the siphon with
the enclosed parts.
Ensure that the drainage hose is not
kinked, crushed or twisted and that
there is no cover plate in the drainage
to prevent the waste water from flowing
out!

Fresh water connection

– Connect the fresh-water connection to
the tap according to the installation
instructions with the enclosed parts.
Ensure that the fresh-water connection
is not kinked, crushed or twisted.
– When replacing the appliance, always
use a new water supply hose.
Water pressure:
at least 0.05 MPa (0.5 bar), maximum
1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing valve
ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
for cold water connection only.

Electrical connection

– Connect the appliance to an
alternating current only, ranging from
220 V to 240 V and 50 Hz or 60 Hz
via a correctly installed socket with
protective earth conductor. See rating
plate for required fusing 9*.
– The socket must be near the appliance
and freely accessible following
installation.
If the plug is not freely accessible, an
allpole disconnector with a contact
opening of at least 3 mm must be
fitted on the installation side to satisfy
the relevant safety instructions.
– The connection may be modified by
technicians only.
– A power cord extension may be
purchased from customer service only.
– Use only a residual current operated
circuit-breaker which features
the symbol ‚. Only this extension
guarantees compliance with
the currently valid regulations.
– The appliance features a water
damage protection system. Please
note the system will not function
unless the power supply is connected.

Removing the appliance

Also observe the sequence of worksteps
here.
– Disconnect the appliance from
the power supply.
– Turn off the water supply.
– Disconnect the waste water and fresh
water connections.
– Loosen fastening screws for the
furniture parts.
– If fitted, remove the base panel.
– Pull out the appliance, carefully pulling
the hose behind.
aus
21