OBJ_BUCH-1994-001.book Page 18 Tuesday, October 1, 2013 2:18 PM
18 | English
select the maximum stroke rate. Firmly hold the machine
against the workpiece and by tilting the machine, slowly
plunge the saw blade into the workpiece.
When the base plate 9 fully lays on the workpiece, continue
sawing along the desired cutting line.
Parallel Guide with Circle Cutter (Accessory)
Parallel Cuts (see figure H): Loosen the locking screw 26 and
slide the scale of the parallel guide through the lead 13 in the
base plate. Set the desired cutting width as the scale value on
the inside edge of the base plate. Tighten the locking screw
26.
Circular Cuts (see figure I): Set the locking screw 26 to the
other side of the parallel guide. Slide the scale of the parallel
guide through the lead 13 in the base plate. Drill a hole in the
workpiece centred in the section to be sawn. Insert the cen-
tring tip 28 through the inside opening of the parallel guide
and into the drilled hole. Set the radius as the scale value on
the inside edge of the base plate. Tighten the locking screw
26.
Coolant/Lubricant
When sawing metal, coolant/lubricant should be applied
alongside cutting line because of the material heating up.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
For safe and proper working, always keep the machine
and ventilation slots clean.
Clean the saw blade holder regularly. For this, remove the saw
blade from the machine and lightly tap out the machine on a
level surface.
Heavy contamination of the machine can lead to malfunc-
tions. Therefore, do not saw materials that produce a lot of
dust from below or overhead.
Lubricate the guide roller 10 occasionally with a drop of oil.
Check the guide roller 10 regularly. If worn, it must be re-
placed through an authorised Bosch after-sales service agent.
The plastic sliding shoe 12 should be replaced when it is
worn.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
1 619 P11 351 | (1.10.13)
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: (0844) 7360109
Fax: (0844) 7360146
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
Fax: (031) 7012446
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: (021) 5512577
Fax: (021) 5513223
Bosch Power Tools
Seite drucken