DSC PC5102-433 Installationshandbuch - Seite 5

Blättern Sie online oder laden Sie pdf Installationshandbuch für Sicherheitssystem DSC PC5102-433 herunter. DSC PC5102-433 13 Seiten.

Seite drucken

Opening/Closing By Wireless Key Reporting

NOTE

NOTE: The Identified Wireless Key Closing option is only available with the PC5020, P-

NOTE

8+, PC501X v2.0 and higher, P832/DL v2.0 and higher, PC1555(MX), P-6B(MX), PC580

v2.0 and higher, P-48 v2.0 and higher by turning section [015] option 4 off.

To enable the reporting of openings and closings by identified wireless keys:

• Make sure the control panel is v2.0 or higher

• Program a valid access code for each key

• Program a closing and opening reporting code for each key's access code

• Turn off the Quick Arm option in section [015] option [4] of the control panel

programming

To ensure that an unidentified wireless key cannot disarm the system, turn off section

[017], option [1] (in the control panel programming). This option is available in control

panels with software version 2.1 or higher.

Command Output Activation

NOTE

NOTE: The Identified Wireless Key Command Output Activation feature is only available

NOTE

with the PC5020, P-8+, PC501X, P832/DL, PC1555(MX), P-6B(MX), PC580 v2.0 and higher

and P-48 v2.0 and higher.

To enable command output activation by wireless keys, ensure that:

• The control panel is v2.0 or higher

• Program a valid access code for each key

• Enable the PGM output attribute Requires Access Code for each PGM output

programmed as [✱][7][1-4] in sections [141] to [154].

Now that you have enrolled all the wireless keys, you will need to program the system to

work properly with the keys. See section 4 for more information.

Section 4: Other Programming

4.1

PC5102 PGM Outputs

The PC5102-433 has two on-board Form C relay PGM outputs. Each of these can be

individually programmed to:

1. Follow main panel PGM outputs 1 to 14.

NOTE: Please refer to your System Installation Manual for available PGM outputs.

NOTE: If the PC5102-433 is connected to the PC580/PC1555/P-48/P-6B (all versions),

PC5010 v1.x, P832 v1.x or the WSS5010 1.0, 2.1, the PC5102 PGM outputs cannot be

programmed to follow main panel PGM outputs 1 or 2.

2. Activate for a programmable amount of time when a signal is received from a

wireless key programmed with output option 31 or 32 (PC5102 PGM pulse) and the

PGM output programming section [92] or [93] is programmed with option 15

(PC5102 PGM pulse). The amount of time that the PGM outputs can be

programmed to remain on is programmed in sections [94] and/or [95]. The default

activation time is 5 seconds.

3. Toggle state when a signal is received from a wireless key programmed with option

31 or 32 and the PGM output programming section [92] or [93] is programmed

with option 16 (PC5102 PGM toggle).

4.2

Enable PC5102-433 Supervision

The control panel will supervise the PC5102-433 receiver via the Keybus after at least one

key has been enrolled on the module (see section 3.2 "Enrolling Wireless Keys").

To activate module supervision, after you enroll the first key(s):

1. Exit and then re-enter installer's programming.

2. Enter programming section [902]. Wait approximately one minute.

3. To exit press [#].

firealarmresources.com