DSC Force2 F2-200 Series Einbauanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Einbauanleitung für Sicherheitssensoren DSC Force2 F2-200 Series herunter. DSC Force2 F2-200 Series 2 Seiten.

Seite drucken

DSC Force2 F2-200 Series Einbauanleitung

With the circuit board removed, use a small screwdriver to punch

out the wiring and mounting knockouts located in the detector's

back. Feed the wiring through the wiring knockout and secure the

detector to the wall.

DM-C AND DM-W DETECTOR MOUNTING BRACKETS

Use the optional DM-W wall-mount

and DM-C ceiling mount brackets to

solve difficult placement problems.

The DM-W and DM-C mount to either

the wall or ceiling and allow for full

vertical and horizontal positioning of

the motion detector - the detector can

be tilted up or down and rotated

through 90° to obtain the best position

for optimal coverage. The Force2 has

been designed to be fully compatible

with the DM-W and DM-C brackets.

Contact your DSC distributor for more

information.

IMPORTANT NOTE: Maximum

detection coverage occurs when the

Force2 is mounted at the height specified in the mounting

instructions and the mounting surface is vertical. If this cannot

be achieved with a mounting bracket, then detector coverage

may be less than specified.

WIRING

Once the detector is mounted in the desired location, connect the

wiring as shown below. Note that various models have the following

optional features.

FORCE 2 - OPTIONS

F2-200 ....................... 'A' Alarm contact only

F2-200

F2-201 ....................... 'A' Alarm contact & Tamper switch

F2-201

F2-202

F2-202 ....................... 'C' Alarm contact & Tamper switch

F2-202

NOTE: Contacts are shown in the non-alarm state with power

applied to the detector.

Wiring shall be insulated with PVC, TFE, PTFE, FEP neoprene or

polymide.

POWER UP

Upon application of power, the alarm indicator will be illuminated

for 60 seconds to indicate the unit is warming up. During this

period, the alarm relay is held in its normal non-alarm state. After

the 60 second warm-up period, the alarm indicator will go out and

the unit will respond to motion in the protected area.

ALARM INDICATOR ON/OFF JUMPER J1

With jumper J1 OFF, the alarm indicator will turn on each time the

unit goes into alarm. With J1 ON, the alarm indicator is disabled.

RANGE ADJUSTMENT

The detector's range is adjustable from about 10' minimum to 40'

maximum (3m minimum to 13m maximum). Rotating the "MW

Adjust" potentiometer clockwise increases the range; rotating the

potentiometer counter-clockwise decreases the range. For

optimum performance, the range should be adjusted so that it

matches the size of the area to be protected. The unit is factory-

set for maximum range.

It is strongly recommended that the range of the detector be

adjusted to match the size of the protected area. To do this, first,

set the LED jumper to the OFF position to enable the LED.

Have someone walk at the farthest spot from the detector that is still

within the desired detection area. Adjust the "Range Adjust"

potentiometer until the alarm LED no longer illuminates when the

person walks through the extreme edge of the detection area.

When so adjusted, readjust the potentiometer so that the unit will

go into alarm when a person walks at the extreme edge of the

detection area.

CAUTION: Microwave frequencies can penetrate walls and

glass. Adjust the range so that it does not extend outside the

desired area of detection.

COMPONENT LOCATIONS

DM-C

Ceiling Mounting Bracket

DM-W

Wall Mounting Bracket

WALK TESTING

It is imperative that the unit be thoroughly walk tested after mounting

and any necessary adjustment be made to ensure that coverage

extends over the desired area. Refer to the 'Range Adjustment'

section of these instructions.

Once coverage has been confirmed, Jumper J1 may be set to the

ON position to disable the alarm LED indicator.

IMPORTANT NOTE: Upon installation, the unit should be

thoroughly tested to verify proper operation. The end user should

be instructed on how to perform walk tests, and should perform a

walk test at least once per year.

PIR LENS

The PIR lens is mounted with the textured

side facing in (smooth side facing out).

Note that the long lens elements are at the

top when the lens is properly positioned.

Ensure the lens is properly seated, and

that the lens holder is securely snapped

into place.

LIMITED WARRANTY

Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product

shall be free of defects in materials and workmanship under normal use and that in fulfilment of any breach of such

warranty, Digital Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return

of the equipment to its repair depot. This warranty applies only to defects in parts and workmanship and not

to damage incurred in shipping or handling, or damage due to causes beyond the control of Digital Security

Controls Ltd. such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of

abuse, alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other

warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security

Controls Ltd. Digital Security Controls Ltd. neither assumes responsibility for, nor authorizes any other person

purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or

liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages, loss

of anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase,

installation or operation or failure of this product.

Motion detectors can only detect motion within the designated areas as shown in their respective installation

instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not

provide volumetric area protection. They have multiple beams of detection and motion can only be detected in

unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings,

floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional or

unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or any

other part of the detection system will impair its proper operation.

Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be

reduced when the ambient temperature rises near or above body temperature or if there are intentional or

unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters, radiators,

stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on.

WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a

regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical

disruption, it is possible for this product to fail to perform as expected.

IMPORTANT INFORMATION

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY DIGITAL SECURITY CONTROLS

LTD. COULD VOID THE USER'S AUTHORITY TO OPERATE THIS EQUIPMENT.

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

Ce dispositif satisfait aux exigences d'Industrie Canada, prescrites dans le document CNR-210. son utilisation

est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l'utilisateur du

dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de

compromettre le fonctionnement du dispositif.

Toronto, Canada • www.dsc.com

Printed in Canada

is a registered trademark of Digital Security Controls Ltd.

29001544 R003