Atwood 8520 Technisches Installationshandbuch

Blättern Sie online oder laden Sie pdf Technisches Installationshandbuch für Furnace Atwood 8520 herunter. Atwood 8520 7 Seiten. 8500-iv series

Seite drucken
ENGLISH, FRANCAIS
THIS INSTRUCTION MANUAL IS FOR USE BY AN AUTHORIZED SERVICE
TECHNICIAN TO INSTALL AN ATWOOD
:
TO THE INSTALLER
THESE INSTRUCTIONS MUST BE SUPPLIED WITH THE FUR
NACE TO THE CONSUMER
:
TO THE CONSUMER
PLEASE RETAIN THESE INSTRUCTIONS FOR FURTHER REFER
.
ENCE
This furnace design has been certified for installation in recre-
ation vehicles as a MSP Category III furnace. Follow this installa-
tion instruction to insure safe operation of the furnace. Failure to
install furnace according to this installation instruction nullifies
the furnace warranty.
SAFETY ALERT SYMBOLS
Safety Symbols alerting you to potential personal safety hazards.
Obey all safety messages following these symbols.
WARNING
avoid possible
injury or death
FIRE OR EXPLOSION
• If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.

FOR YOUR SAFETY

FIRE OR EXPLOSION
WHAT TO DO
IF YOU SMELL GAS
• Evacuate
persons from vehicle.
ALL
• Shut off gas supply at gas container or source.
•
touch any electrical switch, or use any phone or
DO NOT
radio in vehicle.
•
start vehicle's engine or electric generator.
DO NOT
• Contact nearest gas supplier or qualified Service Technician
for repairs.
• If you cannot reach a gas supplier or qualified Service
Technician, contact the nearest fire department.
•
turn on gas supply until gas leak(s) has been repaired.
DO NOT
Installation and service must be performed by a qualified
Service Technician, Service Center or gas supplier.
9
(et Canada)
- hydro flame
FURNACE
TM
.
CAUTION
avoid possible
injury and/or property damage
WARNING
WARNING
.
FURNACE SPECIFICATIONS
-
DIMENSIONS
........................................................................
WEIGHT
-
MINIMUM CLEARANCE TO FLOORBOARDS
&
SIMILAR COMBUSTIBLE BUILDING MATERIALS
SAFETY INFORMATION
FURNACE INSTALLATION
..........................................................................
WALL CUTOUTS
................................................................................
DUCTING
Required Minimum Discharge Chart
Flexible Ducting
........................................................................
Floor Ducting
OPTIONAL INSTALLATION
OPTIONAL INSTALLATION
OPTIONAL INSTALLATION
PROPANE GAS CONNECTION
ELECTRICAL CONNECTIONS
Conductor Sizing Table
Thermostat Installation
DOOR INSTALLATION
Horizontal and Vertical Door Option
Recess Bezel Door Option
DRAFT CAP ASSEMBLY
OPTIONAL FURNACE INSTALLATION
SYSTEM CHECK TESTS
PROPANE GAS PRESSURE
........................................................................
STATIC PRESSURE
DC WIRING DIAGRAM
............................................................................
ILLUSTRATIONS
REPLACEMENT PARTS LIST
SPECIFICATIONS
#
MODEL
BTU Input
Duct Static Pressure
12 Volt Amperage (AMPS)
Watts
Power Supply (
VOLT DC
Recommended Return Air
MINIMUM RETURN AIR
DIMENSIONS
ALL MODELS
Casing
Door
Recess Bezel
1
LITERATURE NUMBER
hydro flame
8500-IV Series Furnace
8516, 8520, 8525,
MODELS
Technical Installation Manual
•Installation •Maintenance
INDEX
..............................................................
..................................................................
,
,
WALLS
..................................
..................................................................
..................................................................
............................................
......................................................................
..................................
-
BOTTOM DISCHARGE KIT
......................................
-
EXTENSION BOX KIT
........................................
-
FLEX ADAPTER KIT
............................................................
..............................................................
............................................................
............................................................
....................................................................
............................................
........................................................
..................................................................
-
Recessed Furnace
....................................................................
..............................................................
......................................................................
..............................................
&
DRAWING
8516-IV
8520-IV
8525-IV
16,000
20,000
25,000
.20˝ W.C.* .10˝ W.C.* .10˝ W.C.* .10˝ W.C.* .10˝ W.C.*
4.6
4.6
7.6
55
55
91
)
12
12
12
80 in
2
80 in
2
80 in
65 in
2
65 in
2
65 in
WIDTH
HEIGHT
DEPTH
16-1/2˝
7-3/8˝
18˝
19-1/4˝
9-1/4˝
1/4˝
20-9/16˝
11-1/2˝
MPD 33179
TM
8531, 8535
Effective 1/08
1
1
1
2
1-2
2
2
2-3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
........................
4-5
5
5
5
5
6
7
(W.C. = Water Column)
8531-IV
8535-IV
30,000
34,000
7.6
9.8
91
118
12
12
2
80 in
2
80 in
2
2
65 in
2
65 in
2
WEIGHT
30 lbs
FURNACE
32 lbs
SHIPPING