DANLERS TLSW HB BP1246 Hinweise zur Installation - Seite 2

Blättern Sie online oder laden Sie pdf Hinweise zur Installation für Schalter DANLERS TLSW HB BP1246 herunter. DANLERS TLSW HB BP1246 2 Seiten. Plated heater boost / multi-selector switches
Auch für DANLERS TLSW HB BP1246: Hinweise zur Installation (2 seiten)

Seite drucken

Wiring diagram

Heater Boost

LIVE

~ 230 Vac

NEUTRAL

Troubleshooting

The heater boost resets itself off:

• The supply to the heater boost switch must be permanent, it

should not be wired in series after another timer device.

The main heating timer is not functioning:

• The heater boost switch can only be wired in parallel with relay

output timer units, otherwise the output of the other timer may be

damaged.

Precautions and Warranty

This product conforms to BS EN 60669-2-1.

Please ensure the most recent edition of the appropriate local wiring regulations are observed

and suitable protection is provided e.g. 6 amps over current, 1kV over voltage. Please ensure

that this device is disconnected from the supply if an insulation test is made.

This product is covered by a warranty which extends to 5 years from the date of manufacture.

Products available from DANLERS

• PIR occupancy switches • Daylight linked dimmers • Manual high frequency dimmers

• Photocells • Radio remote controls • Time lag switches • Outdoor security switches

• Dimmers • Heating, ventilation and air-conditioning controls • Bespoke / O.E.M. products

Please call for more information or a free catalogue, or visit our website.

DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.

Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388

E-mail: [email protected]

Web: www.danlers.co.uk

Company Registered Number 2570169 VAT Registration Number 543 5491 38

16/03/12

LOAD

NEUTRAL

INS992 TLSWHB

Plated heater boost switch

TLSW HB

TLSW HB BP

DANLERS plated heater boost switch can be mounted onto a standard

back box and needs a neutral connection. It can switch a resistive

heating load up to 3kW.

The plate incorporates four red LEDs, each representing a different

remaining time range. Each time the button is pressed the remaining

time advances to the next value, giving a longer time lag. If the button

is pressed when the fourth LED is lit the load is switched off.

The four time lags periods are as follows:

TLSW HB

Marked plate with ¼, ½, 1 and 2 hour periods

TLSW HB BP

Blank plate with ¼, ½, 1 and 2 hour periods

TLSW HB BP1246 Blank plate with 1, 2, 4 and 6 hour periods

The heater boost switch can be wired in parallel with any other relay

output timers as a manual override.

These switches can only be connected to a 230V, 50Hz ac supply.

They can switch up to 13 amps (3000W) of Resistive loads

Or they can also switch up to 1 amp (250W) of fans

For larger loads they can be used to operate a contactor.

Installation procedure

1. Please read these notes carefully before commencing work.

In case of doubt please consult a qualified electrician.

Make sure the power is isolated from the circuit.

Remove the top and bottom lugs if using a 4 lug metal back box.

2. The TLSW HB switches have a terminal block on the reverse, which

should be connected as shown in wiring diagram overleaf:

Live input

Switched Line output

Neutral (two neutral terminals are available)

3. Turn on the supply and test the function of the switch.

Installation notes

TLSW HB BP1246