aevit 2.0 Installationshandbuch - Seite 12
Blättern Sie online oder laden Sie pdf Installationshandbuch für TV-Halterung aevit 2.0 herunter. aevit 2.0 17 Seiten. Mounting brackets
Seite druckenprIMArY INpUT
2.5 OThEr MOUNTINg OpTIONS
(CONTINUEd)
ATTAChINg ONLY ThE INpUT dEVICE SwIVEL BrACkET (CONTINUEd)
sTEP 1
Remove the Input Device Articulating Swivel
Bracket from the quick Adjust Upper Pole. (See
Figure 8, Page 2-5 for information on this assem-
bly). Also, remove the Input Device Swivel Bracket,
(1) 2" Dia rubber washer, and Adjustment Knob
1 (Figure 9, Page 2-5). These components will be
used in step 5 of this section.
sTEP 2
At this point, there will be a threaded rod protrud-
ing from the quick Adjust Upper Pole. Insert the
3/8" Flat Washer and Adjustment Knob 1 onto the
Threaded rod (Figure 23a). This hardware will be
used to lock the quick Adjust Upper Pole in place
much like step 2 Page 2-5. Tighten the adjustment
knob and make a mark on the threaded rod such
that it can be cut as to not protrude from the top
of the adjustment knob when the installation
is completed (Figure 23b). This can be done by
simply making a mark on the rod at the top of
Adjustment Knob 1 and then removing the knob
and washer and cutting the threaded rod approxi-
mately 1/4" beneath the mark. (Figure 24a).
hINT:
PRIOR TO CUTTING ThE ThREADED ROD, ThREAD
(1) 3/8" NUT (NOT INCLUDED) ONTO ThE ThREAD-
ED ROD, ThEN MAKE ThE CUT. AFTER ThE ROD IS
CUT, REMOVE ThE 3/8" NUT FROM ThE CUT END OF
ThE ROD TO CLEAN/DEBUR ThE ThREADS.
Figure 24b shows what this assembly should look
like after cutting the threaded rod.
sTEP 3
Reinstall Adjustment Knob 1 and (1) 3/8" flat
washer as shown in Figure 23a
sTEP 4
Once the quick Adjust Upper Pole is in position, a
3/8" thru hole will need to be drilled into it. Notice
in Figure 25, there is a support webbing under-
neath the quick Adjust Upper Pole. The 3/8" thru
hole can be drilled anywhere along either of the
two (2) dotted lines shown in Figure 26. Basically,
the 3/8" hole will need to be drilled 7/8" from ei-
ther side of the quick Adjust Upper Pole such that
the nylon and flat washers of the Input Device
Swivel Bracket will not interfere with the support
webbing underneath.
(BrkT-AEVIT-FLr & BrkT-AEVIT dOOr)
ADjusTMENT
kNOb 1
3/8" FlAT
QuIck ADjusT
wASHER
uPPER POlE
THREADED
ROD
FIGuRE 23a
Make cut
here
cuT MARk
3/8" NuT
(see hint)
FIGuRE 24a
suPPORT
wEBBINg
FIGuRE 25 - QuIck ADjusT uP-
PER POlE: uNDERsIDE
AEVIT 2.0 MOUNTING BRACKETS INSTALL MANUAL
Make cut Mark flush with the
top of the adjustMent knoB
cuT MARk
FIGuRE 23b
FIGuRE 24b
3/8" hOlE cAN bE DRIllED
ALONg EITHER DOTTED
LINE SHOwN
7/8"
7/8"
FIGuRE 26 - QuIck ADjusT uP-
PER POlE: TOPsIDE
2-9