Austa AU-1P20002G-230-EU Installations- und Betriebshandbuch - Seite 4

Blättern Sie online oder laden Sie pdf Installations- und Betriebshandbuch für Inverter Austa AU-1P20002G-230-EU herunter. Austa AU-1P20002G-230-EU 13 Seiten.

Seite drucken

1. INTRODUCTION

1.1 Prefix

Dear customer, thank you for choosing the AUM-2000 micro inverter from

Austa. We hope you will find our products meet your need for renewable

energy. Meantime, we appreciate your feedback regarding our products.

1.2 Grid-tied PV System

Grid-tied PV system consists of PV panels, grid-tied inverter and junction boxes.

The DC output from the PV panels is converted into AC energy and feedback to

the grid through the AUM-2000. AUM-2000 PV micro inverter contains isolation

transformer with basic insulation between PV input and AC grid output.

1.3 How to Use This Manual

This manual provides detailed product information and installation instructions

for the AUM-2000 micro solar inverter. Please read through this manual before

installation and operation.

WARNING: This indicates a situation where failure to follow instructions may be

a safety hazard or cause equipment malfunction. Use extreme caution and

follow instructions carefully.

1.4 Label

Label is located on the side of the inverter. The information on the label includes

technical data as well as type and serial number of the device. Safety instructions

are listed and explained below:

Danger!

The term "danger" describes an issue which, if ignored can cause

personal injury.

Attention!

With the term "attention" a circumstance is listed which may

cause property damage if disregarded.

Instructions for use!

Under "Instructions for Use", it is pointed out that installation and

operating instructions are to be read and understood before

installation or repair.

Caution, hot surface!

Under "Caution, hot surface", it should be noted that surfaces of

equipment may be hot and create a burn hazard.

Special disposal instructions!

With "Note Separate Disposal", it is pointed out that this product

may not be disposed of with normal garbage. An improperly

conducted disposal can lead to damage to the environment.

CE mark

The product complies with essential requirements of relevant

directives of EU

2. SAFETY INSTRUCTION

WARNING:

PLEASE READ THIS MANUAL BEFORE INSTALLATION. ANY DAMAGE TO THE PRODUCT DUE TO NOT

FOLLOWING THIS MANUAL IS NOT COVERED BY THE WARRANTEE.

ALL THE INSTALLATION SHOULD BE DONE BY CERTIFIED ELECTRICIAN.

BESIDES THE CABLE CONNECTORS, NOTHING INSIDE THE INVERTER SHOULD BE MODIFIED.

ALL INSTALLATION SHOULD FOLLOW THE LOCAL ELECTRIC CODES. FURTHER PROTECTION ON THE

AC WIRING FROM THE INVERTERS SHOULD BE PROVIDED AND MAY BE REQUIRED BY LOCAL AND

NATIONAL WIRING REGULATIONS. THIS PROTECTION IS LIKELY TO INCLUDE RESIDUAL CURRENT

DEVICES, EARTH FAULT MONITORS AND CIRCUIT BREAKERS. THIS PRODUCT MAY CAUSE AC

CURRENT WITH A DC COMPONENT.

IF A RESIDUAL CURRENT-OPERATED PROTECTIVE DEVICE

(RCD) OR A MONITORING DEVICE (RCM) IS USED FOR PROTECTION IN CASE OF DIRECT OR

INDIRECT CONTACT, ONLY AN RCD OR RCM OF TYPE B IS ALLOWED ON THE AC SIDE OF THIS

PRODUCT.

NEVER DISCONNECT PV MODULE FROM THE MICRO-INVERTER WITHOUT FIRST ISOLATING THE AC

MAINS.

ALL PV CONNECTORS AND AC CONNECTORS ARE FORBIDDEN TO BE DISCONNECTED

UNDER LOAD BEFORE SWITCHING OFF THE CIRCUIT BREAKER ON THE AC BRANCH.

PLEASE CONTACT AUTHORIZED SERVICE AGENTS FOR ANY SERVICE WORK.

AU-1P20002G

IS A GRID-TIED SOLAR INVERTER.

UTILITY COMPANY TO CONNECT IT TO THE POWER GRID.

AU-1P20002G

DOES NOT INCLUDE COMPONENTS THAT CAN BE SERVED BY CUSTOMERS.

WARNING:

WHEN THE PHOTOVOLTAIC ARRAY IS EXPOSED TO LIGHT, IT SUPPLIES A DC VOLTAGE TO THE

MICRO-INVERTER.

3. FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and the receiver.

● Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

● Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance may void the user's authority to operate the equipment.

IT MAY REQUIRE APPROVAL FROM LOCAL