ADEMCO VISTA 5140XM Benutzerhandbuch - Seite 3

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Sicherheitssystem ADEMCO VISTA 5140XM herunter. ADEMCO VISTA 5140XM 15 Seiten. Commercial fire & burglary alarm system

Seite drucken

SYSTEM OVERVIEW

FIRE & BURGLARY PROTECTION

One or more sensing devices will have been

assigned by the installer of your alarm

system to each of the various fire and

burglary protection zones in your system

(although not every zone may have been

used). For example, stockroom smoke

detectors may have been assigned to zone

01, hallway fire pull stations to zone 02, the

sensing device on your Entry/Exit door to

zone 03, sensing devices on store front

windows to zone 04 and so on. These

numbers will appear on the console display

window along with an alpha descriptor for

that zone (if programmed), when the

respective zone is faulted.

The fire portion of your alarm system is

always on. When a fire alarm condition is

detected, the console will produce an

interrupted sound and the external fire

warning sounders will produce either a

continuous or interrupted sound depending

on which was selected by your installer. A

message will appear in the console display

window that identifies the zone(s) causing

the fire alarm. In addition, if your system is

connected to a central monitoring station, a

fire alarm report will be sent to that

monitoring station. Refer to the fire alarm

system sections of this manual for a

description of procedures for silencing fire

alarms, bypassing fire zones and activating

a fire drill test.

SUMMARY OF ARMING MODES

Mode

Features For Each Arming Mode

Exit Delay

Entry Delay

AWAY

Yes

STAY

Yes

INSTANT

Yes

MAXIMUM

Yes

BURGLARY SYSTEM ENTRY/EXIT DELAYS

If used, the burglary portion of your system

is programmed by the installer with a preset

time delay, during which the system must be

disarmed upon entering or an alarm will

occur. This feature allows you to leave and

reenter through the entry delay door without

setting off the alarm. The entry delay feature

can also be turned off for greater security

when sleeping or while away for extended

periods of time (INSTANT & MAXIMUM

modes). See your installer for your delay

times.

– 4 –

The burglary portion of your alarm system

(if used) must be armed before it will sense

burglary alarm conditions. When an alarm

occurs, both the console and the external

burglary alarm sounder will produce a

continuous sound. A message will appear

in the console display window that

identifies the zone(s) causing the burglary

alarm and a burglary alarm report will be

sent to the central monitoring station (if

your system is so connected). Disarming

the system will stop alarm sounding. Your

system provides four modes of burglary

protection: STAY, AWAY, INSTANT and

MAXIMUM and even lets you BYPASS

selected zones of protection while leaving

the rest of the burglary system armed. The

system also provides a CHIME mode, for

alerting users to the opening and closing of

doors and windows while the system is

disarmed. Refer to the burglary alarm

section of this manual for a description of

procedures for using these features.

Perimeter Armed

Interior Armed

Yes

Record your delay times here:

Entry Delay 1:

Entry Delay 2:

Exit Delay 1:

Exit Delay 2:

Delays may be no more than 60 seconds

for Exit delay or 45 seconds for Entry delay

for a UL Listed Commercial burglary

application.

SYSTEM OVERVIEW

USER SECURITY CODES

The 5140XM allows up to 99 4-digit user

security codes to be programmed. These

codes are entered at the console's keypad

and are used to operate the system.

When programmed, each code is assigned

an authority level which determines the

system functions that code can perform.

For example, some codes can be given

authority to arm/disarm the burglary

system and to bypass fire and burglary

zones. Other codes may be restricted to

arm/disarming the burglary system only.

There are six authority levels: master,

manager, operator A, operator B, operator

C & duress. Generally speaking, the

master code is intended to be known and

used only by the building owner. The

manager code is intended to be known and

used only by the building superintendent,

the building security officer or the like.

These codes allow full control over system

operation. The operator's codes are

intended to be used by individuals who

need limited and/or temporary control over

system operation. The duress code allows

a silent panic report to be transmitted to

the central station when the user is forced

to arm or disarm under threat. Refer to the

"ADDING, CHANGING AND DELETING

USER CODES" section for detailed

descriptions of the functions that these

codes can perform.

CONSOLE SOUNDS

The console has a built-in sounder which

will produce an interrupted sound for fire

alarms and a continuous sound for

burglary alarms. This sounder will also

"beep" during certain system functions,

such as when depressing keys to operate

the system (to acknowledge the key

press), during entry/exit delay times and

during chime mode. Some of these sounds

can be optionally suppressed. Ask your

installer if this has been done.

All codes can be used interchangeably

when performing system operations within

the limits of each code's authority level. For

example, the burglary system may be

armed with an operator's code and then

disarmed with a master or manager's

codes. Note that an operator C code can

only disarm the burglary system if it was

used to arm the system.

Your installer will have programmed at

least one master code and possibly several

other types of codes at installation time.

Make sure you have a record of the codes

that were programmed. The master and

manager's codes may be used to add,

change or delete additional codes for

temporary users on an "as needed" basis.

Refer to the "ADDING, CHANGING AND

DELETING USER CODES" section for

more information.

BASIC PROCEDURE

To perform most system functions, simply

enter your code, then press the key for the

desired function. To disarm the burglary

system or clear the console display, enter

your code, then press the OFF [1] key.

This is referred to in this manual as the

"OFF" sequence.

NOTE: if "Quick Arming" was programmed

by the installer, the [#] key can be pressed

in place of the security code when arming

the burglary system. The security code

must still be used to disarm the system.

SELF-HELP FEATURE

Abbreviated user's instructions are built

into the system that can be easily viewed

on the alpha console's message display

screen. This feature will prove particularly

useful if this manual is not conveniently

accessible when you need to perform a

seldom used system procedure with which

you are not familiar.

To view the abbreviated instructions,

simply press and hold down the function

key of interest until the description starts to

appear (about 5 seconds) and then release

it. Refer to the FUNCTIONS OF THE

CONSOLE section for detailed descriptions

of each key function.

– 5 –