ADEMCO VISTA-20PS Programmierhandbuch - Seite 7

Blättern Sie online oder laden Sie pdf Programmierhandbuch für Sicherheitssystem ADEMCO VISTA-20PS herunter. ADEMCO VISTA-20PS 17 Seiten.

Seite drucken

MISCELLANEOUS SYSTEM FIELDS (*174-*181)

✱ 174 CLEAN ME REPORTING OPTIONS

(for ESL smoke detectors)

✱ 177 DEVICE DURATION 1, 2

(used in *80 Menu mode-Device Actions 5/6)

✱ 181 50/60 HERTZ AC OPERATION

CONFIGURABLE ZONE TYPE OPTIONS (*182-*185)

✱ 182 CONFIGURABLE ZONE TYPE 90

✱ 183 ZONE TYPE 90 REPORT CODES

IMPORTANT: Use existing Contact ID®

codes, if appropriate, or define unique codes

in CID code range 750-789. See important

note in installation instructions.

✱ 184 CONFIGURABLE ZONE TYPE 91

✱ 185 ZONE TYPE 91 REPORT CODES

IMPORTANT: Use existing Contact ID®

codes, if appropriate, or define unique codes

in CID code range 750-789. See important

note in installation instructions.

SYMPHONY (AUI) ENABLE

✱ 189 Symphony (AUI) ENABLE

(VISTA-20PS Only)

KEYPAD OPTIONS *190-*196 (NOTE: Options for keypad address 16 are set by the factory and cannot be changed.)

NOTE: Each keypad must be assigned a unique address. Keypads programmed with the same address will give

unpredictable results.

✱ 190 KEYPAD 2 DEVICE ADDRESS 17

✱ 191 KEYPAD 3 DEVICE ADDRESS 18

✱ 192 KEYPAD 4 DEVICE ADDRESS 19

✱ 193 KEYPAD 5 DEVICE ADDRESS 20

✱ 194 KEYPAD 6 DEVICE ADDRESS 21

✱ 195 KEYPAD 7 DEVICE ADDRESS 22

✱ 196 KEYPAD 8 DEVICE ADDRESS 23

✱ 197 EXIT TIME DISPLAY INTERVAL

✱ 198 DISPLAY PARTITION NUMBER

(for Alpha Display Keypads)

✱ 199 ECP FAIL DISPLAY

www.PDF-Zoo.com

0 = disable; 1 = Clean Me signal reports;

[0]

Note: If Clean Me is enabled, you must enter "3" in

field ✱56 programming for zone 1 response time.

0 = 15 seconds

[0] [0]

1 = 30 seconds

2 = 45 seconds

3 = 60 seconds

4 = 90 seconds

5 = 2 minutes

0 = 60 Hz; 1 = 50 Hz

[0]

Enter the appropriate value for each entry, 1-10, based on the charts provided on the

next page. Each entry is the sum of the values of its selected options

(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14, #+15=15).

UL: Do not configure zones as a fire alarm or UL burglar alarm zone.

Enter the desired 3-digit Contact ID® report codes for

90 ALARM ID: XXX

alarms and troubles occurring on zones assigned to

TROUBLE ID: XXX

this zone type. Enter the codes sequentially (all 6

digits). When entering digits, [#] moves cursor back, [∗]

moves forward. Press [∗] when done to continue.

Enter the appropriate value for each entry, 1-10, based on the charts provided on the

next page. Each entry is the sum of the values of its selected options

(0-9, #+10=10, #+11=11, #+12=12, #+13=13, #+14=14, #+15=15).

UL: Do not configure zones as a fire alarm or UL burglar alarm zone.

Enter the desired 3-digit Contact ID® report codes for

91 ALARM ID: XXX

alarms and troubles occurring on zones assigned to

TROUBLE ID: XXX

this zone type. Enter the codes sequentially (all 6

digits). When entering digits, [#] moves cursor back, [∗]

moves forward. Press [∗] when done to continue.

Enter each AUI's home partition.

[0] [0]

0 = disabled

AUI 1

AUI 2

1 = partition 1; 2 = partition 2; 3 = partition 3 (common)

NOTE: A minimum of one standard keypad must also be

installed when AUI is used.

[0] [0]

Partition/

Sound

†

Enable

†VISTA-20P: enter partition

VISTA-15P: 1 = enable

0 = disable

†

Part./Enable

Sound

[0] [0]

[0]

– 7 –

6 = 2-1/2 min

7 = 3 min

8 = 4 min

9 = 5 min

#+10 = 6 min

Partition: 0 = keypad disabled; 1-3 = part. no. (3 = com)

Sound:

0 = no suppression

1 = suppress arm/disarm and E/E beeps

2 = Suppress chime beeps only

3 = suppress arm/disarm, E/E, and chime

beeps

See field ∗190 for entries.

0 = no display; 1-5 = seconds between display refresh

0 = no; 1 = yes (partition no. appears on Alpha Display)

0 = 3-digit display ("1" + device address)

1 = 2-digit fixed-display as "91"

#+11 = 7 min

#+12 = 8 min

#+13 = 10 min

#+14 = 12 min

#+15 = 15 min