ADEMCO 5817CB Einbauanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Einbauanleitung für Transmitter ADEMCO 5817CB herunter. ADEMCO 5817CB 2 Seiten. Wireless commercial / household transmitter
Auch für ADEMCO 5817CB: Einbauanleitung (4 seiten), Schnellstart-Handbuch (2 seiten), Handbuch für Installation und Einrichtung (2 seiten), Handbuch für Installation und Einrichtung (2 seiten)

Seite drucken

6. Attach the case back to the mounting plate by sliding the keyhole slots in the case

back down onto the mounting plate's holding posts. The locking tab will click as the case

back locks in place. To disengage the unit from an installed mounting plate, insert a

small screwdriver into the mounting plate release hole, push down to retract the locking

tab, and push upward on the unit to disengage from posts.

Set the DIP switch (after the control panel has enrolled the transmitter's input IDs) for

the desired primary loop characteristics, as described in the table below.

PRIMARY LOOP OPTIONS TABLE

DIP SWITCH POSITION

SWITCH

SETTING

REPEATING

TRANSMISSION

(every 4 sec.)

UPON PRIMARY

SWITCH MUST

LOOP FAULT

ALWAYS BE

Use for high priority

IN THE

alarm, such as fire.

OFF

SINGLE

POSITION

TRANSMISSION

PER PRIMARY

LOOP CHANGE-

OF-STATE

Notes:

a. In order for the control panel to enroll the transmitter, the DIP switches must

be set to OFF – ON – ON – OFF (see Diagram 2).

b. The Auxiliary loops are not affected by the DIP switch settings.

UL REQUIREMENT

1. If using one of the panel revisions shown in the following table, and programming the

5817CB as an Entry/Exit zone, you must enroll the tamper loop (loop 4) as a separate

zone, programmed for 24-hour response (e.g., zone type 5  Trouble-by-day/Alarm-by-

night).

Model #

Rev.

EPROM P/N

FA1600C

(WAVIS150FA-18)

Vista-32FB

(WAVIS32FB-13)

Vista-128FB

(WAVIS128FB-14)

Vista-128B

(WAVIS128B-13)

2. For UL Commercial Burglary installations, this transmitter must be used in conjunction

with the 5881ENHC RF Receiver.

WIRING CONNECTIONS

Connect the loop wiring to the unit's terminals before installing the battery (see Diagram 2).

Notes:

a. Primary loop 1 is a supervised loop and must have an end-of-line (EOL)

resistor (470K ohms, supplied) placed across the last sensor. Additionally, for

Primary loop 1, a contact device may not be installed more than 20 feet from the

transmitter.

b. If loop 2 is not going to be used, the magnet is not necessary.

If loop 3 is not going to be used, no connection is needed across its terminals.

For UL household burglary and fire installations, the loop 3 contact device (if

used) may not be more than 3 feet from the transmitter.

BATTERY INSTALLATION/REPLACEMENT

1. Remove the transmitter's cover as described in Mounting Step 1.

2. Observe correct polarity and insert the battery provided into the battery holder

(see Diagram 2). Take care not to bend the antenna.

SWITCH MUST

ALWAYS BE

IN THE

OFF

POSITION

- 2 -

firealarmresources.com

Note: Replace battery only with: Duracell DL123A, Sanyo CR123A,

Panasonic CR123A, Ademco 466, Varta CR123A, or Tekcell CR123A.

CAUTION:

Risk of fire, explosion, and burns. Do not recharge, disassemble,

heat above 212°F (100°C), or incinerate. Dispose of used batteries

promptly. Keep away from children.

To replace the cover, engage the hooks along the top edge and snap shut.

SPECIFICATIONS

Dimensions

1-9/16"W x 3-1/2"H x 1-3/16"D (40mm x 89mm x 30mm)

Battery 3V Lithium (see BATTERY INSTALLATION/REPLACEMENT).

UL Listings:

Commercial Fire ...................................... UL864

Household Fire......................................... UL985

Household Burg ....................................... UL1023

Commercial Burg ..................................... UL365, UL609, UL634, UL1610

TO THE INSTALLER

Regular maintenance and inspection (at least annually) by the installer and frequent testing

by the user are vital to continuous satisfactory operation of any alarm system.

The installer should assume the responsibility of developing and offering a regular

maintenance program to the user, as well as acquainting the user with the proper operation

and limitations of the alarm system and its component parts. Recommendations must be

included for a specific program of frequent testing (at least weekly) to insure the system's

operation at all times.

FO R D ETA I LS O N LI M I TA TI O N S O F TH E EN TI R E A LA R M

C O N TR O L PA N EL' S I N STA LLA TI O N I N STR U C TI O N S FO R TH E R EC EIV ER / C O N TR O L W I TH

W H I C H TH I S D EV I C E I S U SED .

NOTE:

For UL commercial and household fire

installations, only one initiating device may be

connected to this transmitter. For UL commercial

burglary installations, multiple initiating devices

may be used as long as the devices all service

the same function such as door/window contacts,

motion or glassbreak detectors. All initiating

devices must be located within the same room.

THE DIP SWITCHES MUST BE

SET AS SHOWN DURING

ENROLLMENT BY THE CONTROL

WHITE AREA

INDICATES

SWITCH HANDLE

DIP

SWITCH

OFF

DIP SWITCH FOR PRIMARY LOOP OPTIONS

(SEE SETTINGS TABLE)

SHOWN SET FOR: 1. SINGLE TRANSMISSION

NOTE: SW2 MUST BE ON

SW3 MUST BE ON

COVER

SW4 MUST BE OFF

TAMPER

SWITCH

LOOP 3

TERMINALS

(AUX)

SLOT FOR

CONCEALED

WIRING ACCESS

CONTACT

Diagram 2. Transmitter, Cover Removed

SY STEM , R EFER TO TH E

MOUNTING

PLATE

HOLE

TAMPER SWITCH

HOLD DOWN

CONCEALED

WIRING

ENTRY

HOLE

Diagram 1. Mounting Plate

COVER

HOLDING

ANTENNA

SLOTS (2)

ALIGN MAGNET

WITH MARKS ON

CASE (2 PLACES)

LOOP 2

REED SWITCH

(AUX)

BATTERY

MAGNET

(OBTAIN

SEPARATELY)

1/2"

–

MAX.

PRIMARY

MOUNTING

LOOP 1

PLATE

TERMINALS

COVER

RELEASE

PRY-OFF

POINT

N.O.

N.C.

CONTACT

EOLR

470K ohms

DEVICE

5817CB-002-V1

- 3 -

CASE

HOLDING

POSTS

MOUNTING

PLATE HOLES

LOCKING

TAB

5817CB-001-V0