Automationdirect.com AcuAmp 3ACTR Series Einbauanleitung

Blättern Sie online oder laden Sie pdf Einbauanleitung für Messwertaufnehmer Automationdirect.com AcuAmp 3ACTR Series herunter. Automationdirect.com AcuAmp 3ACTR Series 2 Seiten.

Seite drucken

Specifications

24 VAC/DC ( +/- 10%), Intended for use with a Class

2 source with the secondary fused to limit power to a

maximum of 100 VA

Power Supply

Note: Power Supply and output signal ARE NOT

isolated. Do not connect the negative terminals

to a common point.

Power Consumption

< 6.0 VA

4-20mA

Output Signals

Four outputs, three proportional to the current in that

phase, one an average of all three.

Output Limit

20.8 mA

Output Impedance

500Ω maximum

Accuracy

1.0% FS

Response Time

220ms (90% step change)

3ACT: 50/60Hz, Average Responding

Frequency Range

3ACTR: 30-100Hz, True RMS

1.1x range continuous

Sensed Current Limit

3x range for 6 seconds

6x range for 1 second

Isolation Voltage

UL tested to 1240VAC

Sensing Apertures

0.74 in (18.8 mm) dia.

Case

UL 94V-0 Flammability rated thermoplastic

-Temp -4 to 122°F (-20 to 50°C)

-Humidity 0-95% RH, Non-condensing

Environmental

-Pollution degree 2

-Altitude 2000 meters

cULus listed E197592

Certifications

For products intended for the EU market, the

following is applicable to the CE compliance of

the product:

The 3ACT/3ACTR Series may comply with EN 61010-1 CAT III

300V max line-to-neutral measurement category. If insulated

cable is used for the primary circuit, the voltage rating of the

measurement category can be improved according to the

characteristics given by the cable manufacturer.

Part Number Key

3ACT030 - 42 - 24 - F

HOUSING TYPE

F - Fixed Core

POWER SUPPLY

24 - 24 VAC/DC (non-isolated)

OUTPUT SIGNAL

42 - 4-20mA

CURRENT RANGES

030 - 0-10, 0-15 and 0-30A

100 - 0-30, 0-50, and 0-100A

200 - 0-100, 0-150 and 0-200A

3ACT: 3-phase AC current transducer, average responding

3ACTR: 3-phase AC current transducer, True RMS

Warning! Risk of hazardous voltage

When operating the transducer, certain parts

may carry hazardous live voltage (e.g., primary

conductor, secondary terminals). The transducer

should not be put into service if the installation is

not complete.

Warning! Risk of electric shock or

personal injury

Safe operation can only be guaranteed if

the

is used for the purpose for

transducer

which it was designed and within the limits

of the technical specifications. When this

symbol is used, it means you should consult

all documentation to understand the nature

of potential hazards and the action required

to avoid them.

AutomationDirect.com (ADC)

3505 Hutchinson Road, Cumming, GA 30040

Phone: (800) 633-0405 or (770) 889-2858

3ACT/3ACTR - Inst - Rev 1

0820

P-N 292000612

3ACT/3ACTR

SERIES

INSTALLATION

INSTRUCTIONS

Part No. 3ACT030-42-24-F

Quick Start Guide

1. Mount the 3ACT/3ACTR Current Transducer to a

DIN rail or panel in a suitable enclosure.

2. With monitored load off, install each phase

through the sensing windows. Designate one

phase as A, B, and C.

3. Select the current range using the slide

switch

4. Connect output terminals + and - using 22-14

AWG copper wires rated 75/90°C. Tighten to 5-7

inch-pounds torque.

5. Connect power supply voltage to terminals 9-10.

6. The output will be proportional to the current in

each phase, plus one which is the average of the

three.

7. Any of the four analog signals can be used

independently, or all four can be used at the same

time.