ADEMCO Quest 2235 Einbauanleitung - Seite 4

Blättern Sie online oder laden Sie pdf Einbauanleitung für Zubehör ADEMCO Quest 2235 herunter. ADEMCO Quest 2235 4 Seiten. Microwave/pir motion sensors

Seite drucken

Supervision Failure Indications: If a supervision failure

occurs, it will be indicated by the appropriate LED flashing 2

times per second, regardless of the LED enable/disable option

chosen by DIP Switch. If a PIR failure occurs, the RED LED

will flash; if a microwave failure occurs, the GREEN LED will

flash. If the unit has defaulted to PIR-only operation as a

result of a microwave failure, the RED LED will light when an

alarm occurs, if enabled by DIP Switch while the GREEN LED

continues to flash.

Upon supervision failure, the open collector TROUBLE output

on the terminal block will also go low (requires 1000-ohm pull-

up resistor). Use shielded wire for UL installations.

TO THE INSTALLER

Regular maintenance and inspection (at least annually) by the

installer and frequent testing by the user are vital to

continuous satisfactory operation of any alarm system.

The installer should assume the responsibility of developing and

offering a regular maintenance program to the user, as well as

acquainting the user with the proper operation and limitations

of the alarm system and its component parts. Recommendations

must be included for a specific program of frequent testing (at

least weekly) to ensure the system's operation at all times.

THE LIMITATIONS OF YOUR MICROWAVE/PASSlVE

INFRARED MOTION DETECTOR

While the Intrusion Detector is a highly reliable intrusion detection device, it does not

offer guaranteed protection against burglary. Any Intrusion Detection device is

subject to compromise or failure to warn for a variety of reasons:

• These Motion Detectors can only detect intrusion within the designed ranges as

diagrammed in this installation manual.

• The passive infrared motion sensor in this Motion Dectector do not provide

volumetric area protection. It does create multiple beams of protection, and

intrusion can only be detected in unobstructed areas covered by those beams.

• Passive Infrared Detectors cannot detect motion or intrusion that takes place behind

walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows.

• Metal objects (or other reflectors, such as foil faced insulation or water in bottles)

can alter the microwave sensors protection pattern.

• Mechanical tampering, masking, painting or spraying of any material on the

mirrors, windows or any part of the optical system can reduce the detection ability

of the Passive Infrared Motion Detector.

• Passive Infrared Detectors sense changes in temperature; however, as the

ambient temperature of the protected area approaches the temperature range of

90° to 105°F (32° to 40°C), the detection performance can decrease.

• This Passive Infrared Detector will not operate without appropriate DC power connected

to it or if the DC power is improperly connected (i.e. reversed polarity connections).

• Passive Infrared Detectors, like other electrical devices, are subject to component

failure. Even though they are designed to last as long as 10 years, the electronic

components could fail at any time.

We have cited some of the most common reasons that a Passive Infrared Motion Detector

can fail to catch intrusion. However, this does not imply that these are the only reasons and

therefore, it is recommended that weekly testing of this type of unit, in conjunction with

weekly testing of the entire alarm system, be performed to ensure that the detectors are

working properly.

Installing an alarm system may make the owner eligible for a lower insurance rate,

but an alarm system is not a substitute for insurance. Homeowners, property owners

and renters should continue to act prudently in protecting themselves and continue

to insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems

owe it to themselves and their loved ones to learn about these developments.

ÊN8656V1m

N8656V1 12/98

WARNING

165 Eileen Way, Syosset, New York 11791

MAINTAINING PROPER OPERATION

In order to maintain the detector in proper working condition,

it is important that the following be observed by the user:

1. Power should be provided at all times. Loss of power to the

unit will result in the alarm contacts reverting to an alarm

state. The unit's DC source should have standby power

available for at least 4 hours of operation during

emergencies.

2. Units should never be re-aimed or relocated without the

advice or assistance of the alarm service company.

3. The physical surroundings of the protected area should not

be changed. If furniture or stock is moved, or air

conditioning or additional heating is installed, the system

may have to be readjusted by the alarm service company.

4. Walk-Tests should be conducted frequently (at least

weekly) to confirm proper coverage by each detector.

FEDERAL COMMUNICATIONS COMMISSION (FCC)

STATEMENT

This device complies with Part 15 of FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept

any interference received, including interference that may

cause undesired operation.

ADEMCO LIMITED WARRANTY

Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its

divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York

11791, warrants this detector to be in conformance with its own plans and

specifications and to be free from defects in materials and workmanship under

normal use and service for 72 months from the date stamp control on the product.

Seller's obligation shall be limited to replacing, at its option, free of charge for

materials or labor, a detector which is proved not in compliance with Seller's

specifications or proves defective in materials or workmanship under normal use

and service. Seller shall have no obligation under this Limited Warranty or other-

wise if the detector is altered or improperly repaired or serviced by anyone other

than Ademco factory service. In case of defect, return the detector to ADI or an

authorized distributor for an immediate replacement.

THERE

ARE

WARRANTIES,

MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR

OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE

HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY

CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR

ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER

BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS

CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.

Seller does not represent that its detector may not be compromised or cir-

cumvented; that the detector will prevent any personal injury or property loss by

burglary, robbery, fire or otherwise; or that the detector will in all cases provide

adequate warning or protection. Buyer understands that a properly installed and

maintained alarm may only reduce the risk of a burglary, robbery, fire or other

events occurring without providing an alarm, but it is not insurance or a guarantee

that such will not occur or that there will be no personal injury or property loss as

a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY

PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A

CLAIM THE DETECTOR FAILED TO GIVE WARNING. HOWEVER, IF SELLER

IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR

DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, RE-

GARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL

NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE DETECTOR,

WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST

SELLER. This warranty replaces any previous warranties and is the only warranty

made by Seller on this detector. No increase or alteration, written or verbal, of the

obligations of this Limited Warranty is authorized.

EXPRESS

IMPLIED,