DBI SALA ExoFit NEX 1113758 Handbuch - Seite 2
Blättern Sie online oder laden Sie pdf Handbuch für Sicherheitssensoren DBI SALA ExoFit NEX 1113758 herunter. DBI SALA ExoFit NEX 1113758 16 Seiten. Full body suspension harness
1.0 application
1.1.1 purpose: Suspension harness used for Fall
Arrest (D-Ring connections A, Figure 2) and Work
Positioning (D-Ring connections B, Figure 2).
3.0
Donning anD use
3.9
Donning AnD Fitting the suspension hArness: The ExoFit NEX™ Suspension Harness includes
leg straps for work positioning. Don the Full Body Suspension Harness using the following steps and the
corresponding images in Figure 3.
step 1.
Locate the front of the harness. The front has two D-Rings. Lift up the harness and hold by the
shoulder straps. Ensure all straps are not twisted.
step 2.
With the front of the harness facing forward, step through the right side of the harness with
your right leg. Then, step through the left side of the harness with your left leg. Grasp the right
shoulder strap and place it on the top of your right shoulder. Ensure that the straps are not
tangled and hang freely.
note: Certain models include additional buckles on the leg straps to eliminate the need to
step into the harness while donning. These buckles must be properly connected and adjusted
during the donning process.
step 3.
Grasp the left shoulder strap and place it over your left shoulder. The two D-Rings will be
positioned on the front of your body if the harness has been donned properly.
step 4.
Grasp the tab of the buckle located at the bottom of the strap that you placed over your left
shoulder. Insert the tab into the receptor of the quick connect buckle on the left side of the
harness. You will hear a click when the tab engages properly.
note: Locking
between the sliding bar and slot on the female end of the quick connect buckle. It does
not control engagement or disengagement of the buckle ends and will not affect the buckle
connection in the event of a fall.
step 5.
Grasp the waist-level strap ends on right and left sides of the harness. Pull both ends forward
until all slack is removed from the waist strap and the strap is comfortably tight around your
waist. Insert strap ends into the waist strap keeper loops on the right and left sides of the
harness.
step 6.
Reach between your legs and grasp the leg strap on your right side. Bring the strap up and
insert the tab of the buckle into the receptor of the buckle on the right side. You will hear a click
when the tab engages properly.
step 7.
Connect the right leg strap using the same procedure as in Step 6. To adjust the leg straps,
unlock
keeper on the end of the strap will stop it from pulling completely out of the buckle. When the
strap is properly adjusted, lock
tabs on the buckle towards each other with one hand, while pulling on the tab portion of the
buckle with the other hand.
step 8.
Adjust shoulder straps to a snug fit using the strap adjustment procedure described between
Steps 4 and Step 5 on the following page. Left and right sides of the shoulder straps should be
adjusted to the same length and the upper front D-Ring should be centered on your lower chest.
The back D-Ring should be centered between your shoulder blades. Adjust the leg straps to a
snug fit. At least 3 in. (8 cm) of webbing must extend past the buckle on the leg straps. Adjust
the waist belt again as necessary for a secure, comfortable fit.
and unlocking
the webbing lock on the quick connect buckle and pull on the strap. A plastic end
the webbing lock. To release the buckle, press the silver-colored
Figure 2 - Applications
A
B
the webbing lock prevents or allows the strap to slide
2
A