Garmin STRIKER PLUS 5 Benutzerhandbuch - Seite 15

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Schiffsausrüstung Garmin STRIKER PLUS 5 herunter. Garmin STRIKER PLUS 5 16 Seiten. Compass safe distance
Auch für Garmin STRIKER PLUS 5: Installationsanleitung Handbuch (16 seiten), Schnellstart-Handbuch (2 seiten)

Seite drucken

Appendix

Registering Your Device with the Serial

Number

If your device does not have Wi‑Fi technology, you can register

using the device's serial number. If your device has Wi‑Fi

technology, you should use the ActiveCaptain app to register the

device

(Getting Started with the ActiveCaptain App, page

Keep the original sales receipt, or a photocopy, in a safe place.

Locate the serial number on the product box or on the device.

Specifications

Temperature range

Water rating

Input voltage

Rated current

Fuse

Wireless frequency and protocol* Wi‑Fi, 2.4 GHz @ 22 dBm nominal

*Not available on all models.

Troubleshooting

My device will not turn on or keeps turning off

Devices erratically turning off or not turning on could indicate an

issue with the power supplied to the device. Check these items

to attempt to troubleshoot the cause of the power issue.

• Make sure the power source is generating power.

You can check this several ways. For example, you can

check whether other devices powered by the source are

functioning.

• Check the fuse in the power cable.

The fuse should be located in a holder that is part of the red

wire of the power cable. Check that the proper size fuse is

installed. Refer to the label on the cable or the installation

instructions for the exact fuse size needed. Check the fuse to

make sure there is still a connection inside of the fuse. You

can test the fuse using a multimeter. If the fuse is good, the

multimeter reads 0 ohm.

• Check to make sure the device is receiving is at least 10 V,

but 12 V is recommended.

To check the voltage, measure the female power and ground

sockets of the power cable for DC voltage. If the voltage is

less than 10 V, the device will not turn on.

Changing the Fuse in the Power Cable

Open the fuse housing

Twist and pull the fuse to remove it

Insert a new 3 A fast-blow fuse.

Close the fuse housing.

My device will not acquire GPS signals

If the device is not acquiring satellite signals, there could be a

few causes. If the device has moved a large distance since the

last time it has acquired satellites or has been turned off for

Appendix

From -15° to 55°C (from 5° to 131°F)

IEC 60529 IPX7

From 10 to 20 Vdc

1.5 A

3 A, 250 V fast-acting

longer than a few weeks or months, the device may not be able

to acquire the satellites correctly.

• Ensure the device is using the latest software. If not, update

the device software

ActiveCaptain App, page

• Make sure the device has a clear view of the sky so the

antenna can receive the GPS signal. If it is mounted inside of

a cabin, it should be close to a window so it can receive the

2).

GPS signal.

My sonar does not work

• Push the transducer cable all the way into the back of the

device.

Even if the cable seems to be connected, you should push

firmly so that it is fully seated.

• Press , and ensure sonar is enabled.

• Select the correct transducer type

Type, page

4).

My device is not creating waypoints in the correct

location

You can manually enter a waypoint location to transfer and

share data from one device to the next. If you have manually

entered a waypoint using coordinates, and the location of the

point does not appear where the point should be, the map

datum and position format of the device may not match the map

datum and position format originally used to mark the waypoint.

Position format is the way in which the GPS receiver's position

appears on the screen. This is commonly displayed as latitude/

longitude in degrees and minutes, with options for degrees,

minutes and second, degrees only, or one of several grid

formats.

Map datum is a math model which depicts a part of the surface

of the earth. Latitude and longitude lines on a paper map are

referenced to a specific map datum.

Find out which map datum and position format was used

when the original waypoint was created.

If the original waypoint was taken from a map, there should

be a legend on the map that lists the map datum and position

format used to create that map. Most often this is found near

the map key.

Select Settings > Units.

Select the correct map datum and position format settings.

Create the waypoint again.

My device does not display the correct time

Time is set by GPS position and time zone setting.

Select Settings > Units > Time Zone.

Ensure the device has a GPS fix.

(Updating Software with the

3).

(Selecting the Transducer