Indesit KN6T62SA/I S Betriebsanleitung - Seite 17

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Backofen Indesit KN6T62SA/I S herunter. Indesit KN6T62SA/I S 20 Seiten. Cooker and oven
Auch für Indesit KN6T62SA/I S: Betriebsanleitung (33 seiten)

Seite drucken

condition may be checked.

• Is shorter than 1500 mm.

• Fits firmly into place at both ends, where it will

be fixed using clamps that comply with current

regulations.

! If one or more of these conditions is not fulfilled

or if the cooker must be installed according to the

conditions listed for class 2 - subclass 1 appliances

(installed between two cupboards), the flexible steel

hose must be used instead (see below).

Connecting a flexible jointless stainless steel pipe

to a threaded attachment

Make sure that the hose and gaskets comply with

current national legislation.

To begin using the hose, remove the hose holder on

the appliance (the gas supply inlet on the appliance is

a cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres,

making sure that the hose is not compressed and does

not come into contact with moving parts.

Checking the tightness of the connection

When the installation process is complete, check the

hose fittings for leaks using a soapy solution. Never

use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas

other than the default type (this is indicated on the

rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7 mm socket spanner

(see fi gure), and replace them with nozzles suited to the

new type of gas (see Burner

and nozzle specifi cations table).

3. Replace all the components

by following the above

instructions in reverse.

Adjusting the hob burners'

minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory screw,

which is positioned inside or next to the tap pin, until

the flame is small but steady.

! If the appliance is connected to a liquid gas supply,

the regulatory screw must be fastened as tightly as

possible:

3. While the burner is alight, quickly change the position of the

knob from minimum to maximum and vice versa several times,

checking that the flame is not extinguished.

! The hob burners do not require primary air adjustment.

! After adjusting the appliance so it may be used with a different

type of gas, replace the old rating label with a new one that

corresponds to the new type of gas (these labels are available

from Authorised Technical Assistance Centres).

! Should the gas pressure used be different (or vary slightly) from

the recommended pressure, a suitable pressure regulator must

be fitted to the inlet hose in accordance with current national

regulations relating to "regulators for channelled gas".

Replacing the Triple ring burner nozzles

1. Remove the pan supports and lift the burners out of their housing.

The burner consists of two separate parts (see pictures).

2. Unscrew the nozzles using a 7 mm socket spanner. Replace the

nozzles with models that are configured for use with the new type of

gas (see Table 1). The two nozzles have the same hole diameter.

3. Replace all the components by completing the above operations in

reverse order.

• Adjusting the burners' primary air :

Does not require adjusting.

• Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust the adjustment screw, which is

positioned in or next to the tap pin, until the flame is small but

steady.

3. Having adjusted the flame to the required low setting, while the

burner is alight, quickly change the position of the knob from

minimum to maximum and vice versa several times, checking that

the flame does not go out.