Arcam P349 Handbuch & Anleitungen - Seite 8

Blättern Sie online oder laden Sie pdf Handbuch & Anleitungen für Verstärken Arcam P349 herunter. Arcam P349 13 Seiten. Integrated amplifier/pre-amplifier/power amplifier

Arcam P349 Handbuch & Anleitungen

AMP Device Mode

TUN Device Mode

The A Device Mode button configures the CR902 to
The T Device Mode button configures the CR902 to
control your Arcam amplifier. Pressing this button does
control the tuner functions of Arcam tuners.
not affect the currently selected input on the amplifier.
P
Toggles power between standby and on
P
Toggles power between standby and on
0
9 The numeric keys are used to store and
...
recall presets
DISP
Cycles through the front panel display's
Cycles through the front panel display's
brightness options
DISP
brightness options
MENU
Displays the amplifier setup menu on the
Cycle through different information
INFO
front panel
display modes
Navigate menus
)
Rewind iPod
O confirms a selection
(
Fast forward iPod
@
Toggles the mute function of the amplifier
]
Preset down/Sirius category down/iPod
track back
VOL-
Decrease (
) and increase (
) amplifier
+
[
Preset up/Sirius category up/iPod track
VOL+
volume
forward
SP1
Toggles Speaker 1 output
#
Stop iPod
SP2
Toggles Speaker 2 output
$
Play / pause iPod
BAL
Adjusts the balance between the left and
&
Play / pause iPod
right audio channel
MENU
Displays the tuner setup menu on the front
panel
' , Preset up / down, iPod track back / forward
< >
Decrement / increment tuning frequency
Confirm a selection
O
FM MONO
Toggle FM mode between mono and stereo
reception
P/TUNE
Enter/Exit Preset recall mode
Enter/Exit Preset store mode
STORE
BAND
Cycles through available tuner bands

CD Device Mode

BD Device Mode

The c Device Mode button configures the CR902 to
The B Device Mode button configures the CR902 to
control the CD functions of Arcam CD players.
control the BD functions of Arcam BD players.
P
P
Toggles power between standby and on
Toggles power between standby and on
!
Open/close disc tray
!
Open/close disc tray
The numeric keys allow direct access to
The numeric keys allow direct access to
individual tracks on a disc. To select a track
individual tracks on a disc. To select a track
press the corresponding keypad button.
press the corresponding keypad button.
0
9
0
9
...
...
For tracks greater than 9, enter the digits
For tracks greater than 9, enter the digits
in sequence. For example, to play track 15,
in sequence. For example, to play track 15,
press 1 , then press 5 .
press 1 , then press 5 .
Cycles through the front panel display's
Cycles through the front panel display's
DISP
DISP
brightness options
brightness options
Changes the available display modes on the
Changes the available display modes on the
MODE
MODE
CD player
BD player
Fast rewind
Fast rewind
)
)
(
Fast forward
(
Fast forward
Skip back to the start of the current/
Skip back to the start of the current/
]
]
previous track
previous track
[
Skip forwards to the start of the next track
[
Skip forwards to the start of the next track
#
Stop playback
#
Stop playback
Play
Play
$
$
Toggles pause of playback
Toggles pause of playback
&
&
MENU
Enter a track in a programmed track list
Changes audio decode format (Dolby
AUDIO
Digital, DTS, etc.).
Navigates track listings if supported by the
player
Activates BD player menu.
MENU
O selects the currently highlighted track if
Navigates track listings if supported by the
supported by the player
player
Toggles random ('shuffle') play on and off
O selects the currently highlighted track if
SHUFF
supported by the player
Repeat playback of the disc or pre-
programmed selection of tracks. To repeat
Returns navigation to the top level of the
.
RPT
a particular track, select that track and press
menu ('Home').
twice. To cancel, press
a third time.
RPT
RPT
When navigating a menu, press this key to
RTN
Toggles between selecting the HD and CD
return to the previous screen or selection
SACD
layer of SACD disc
Toggles random ('shuffle') play on and off
SHUFF
Repeat playback of the disc or pre-
programmed selection of tracks. To repeat
RPT
a particular track, select that track and press
twice. To cancel, press
RPT
Toggles between selecting the HD and CD
SACD
E-14
layer of SACD disc
loudspeakers
PHONO
GROUND
PHONO
ONLY
(MM)
CD
TUNER
SAT
R
HF
4–16 OHMS. CLASS 2 WIRING
LF
SPEAKER 1
PHONO
GROUND
PHONO
ONLY
(MM)
CD
TUNER
SAT
R
HF
Remove
LF
metal strip
4–16 OHMS. CLASS 2 WIRING
SPEAKER 1
a third time.
RPT
Connecting
Notes on making speaker connections
loudspeakers
Do not make any connections to any amplifier while it is switched on. We recommend that your
<
amplifier is completely disconnected from the mains supply before starting.
<
Before switching your amplifier(s) on for the first time after connecting to speakers, please check all
There are many different ways of connecting your
connections thoroughly. Ensure that bare wires or cables are not touching each other or the amplifier's
loudpeakers to your A49 or P49/P349 and the following
chassis (which could cause short circuits), and that you have connected positive (+) to positive and
section describes how to connect and configure the
negative (–) to negative. Be sure to check the wiring for both the amplifier and the speaker.
loud speakers and amplifier for the most common
<
After making connections: switch the amplifier(s) on, select a source signal, then gradually increase the
configurations.
volume to the required listening level.
<
If you are unsure as to how your system should be connected, or need advice on bi-amping, please
contact your Arcam dealer who will be happy to help you.
RECORD
PRE
AUX R
AUX L
PRE OUT R
PRE OUT L
TRIGGER OUT
BD
PVR
AV
OUT
OUT
ACCESSORY
POWER
6V
1A 12V
1.5A
R
L
HF
POWER INLET
A49
4–16 OHMS. CLASS 2 WIRING
LF
SPEAKER 2
SPEAKER 2
SPEAKER 1
110-120V/220-240V ~ 50-60 Hz
350W MAX
An A49 connected to speakers using single wiring.
RECORD
PRE
AUX R
AUX L
PRE OUT R
PRE OUT L
TRIGGER OUT
BD
PVR
AV
OUT
OUT
ACCESSORY
POWER
6V
1A 12V
1.5A
R
L
HF
POWER INLET
Remove
A49
4–16 OHMS. CLASS 2 WIRING
metal strip
LF
SPEAKER 2
SPEAKER 2
SPEAKER 1
110-120V/220-240V ~ 50-60 Hz
350W MAX
An A49 connected to two sets of speakers using bi-wiring.
E-15

Normal single wiring

For single wiring, we recommend that you use the
set of terminals on your amplifier. If each
SPEAKER 1
speaker has more than one pair of connecting terminals,
L
use the terminals labelled
or 'Low Frequency'.
LF
Connect the red positive terminal of the right speaker
connection on the amplifier (labelled
) to the positive
R+
terminal of your right speaker. Similarly, connect the
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
black negative terminal of the right speaker connection
SUPPLY
VOLTAGE
on the amplifier (labelled
) to the negative terminal
R-
of your speaker. Repeat the process for the left speaker,
using the terminals labelled
and
on the amplifier.
L+
L-
WARNING: If your speakers support bi-wiring, there will be a
strip of conductive metal connecting the low-frequency (LF)
terminals to the high-frequency (HF) terminals; this MUST NOT
BE REMOVED in a single-wired system.

Bi-wiring

Bi-wiring is performed in the same way as single wiring
L
except that, a pair of cables are used to connect the
amplifier to each speaker.
Follow the instructions given for single wiring; then
perform the same actions, this time connecting the
set of terminals on your amplifier to the
SPEAKER 2
terminals labelled HF or 'High Frequency' for each
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
speaker.
SUPPLY
VOLTAGE
WARNING: Speakers that support bi-wiring have a strip of
metal that connects the low frequency (LF) terminals to the
high frequency (HF) terminals. This MUST BE REMOVED in a
bi-wired system.