Alemite 7342 Service-Handbuch - Seite 6

Blättern Sie online oder laden Sie pdf Service-Handbuch für Kabel und Anschlüsse Alemite 7342 herunter. Alemite 7342 12 Seiten. High-capacity reel

Seite drucken

SER 7342

3. Install Extension Spring (23) into the eye on the Pawl

and onto Spring Post (22).

4. Secure the Spring Post to the Base Assembly with

Nut (1).

• Refer to Figure 2 for the proper hole location.

• Tighten the Nut securely.

Ribbed-Neck Bolts

IMPORTANT: Make sure the longer Bolts (30)

mount on the Pawl Assembly side of the Base

Assembly.

5. Install Bolts (30 and 29) and Washers (28) onto the Base

Assembly as required.

Sheave Assembly

6. Secure Shaft and Flange Assembly (3) to Sheave

Assembly (2) with Screws (5) and Nuts (1).

7. Install Retaining Ring (15) into the furthest inward

groove of Shaft and Riser Assembly (6).

8. Install the Shaft and Riser Assembly into Ratchet (36).

9. Secure the Ratchet assembly to the Sheave Assembly

with Screws (5) and Nuts (1).

10. Position the Sheave Assembly (with attached

components) onto the Base Assembly.

• Make sure the Ratchet side faces the Pawl.

Bearings and Arbor

11. Install Bearing (27) into Bearing Housing (26).

IMPORTANT: Make sure the extended portion

of the Bearing faces inward. See Figure 2.

12. Install the first Bearing and Housing assembly (extended

side first) onto the Shaft and Riser Assembly and onto

the Bolts.

13. Attach the Bearing and Housing assembly to the Base

Assembly with Nuts (1).

• Do not tighten the Nuts at this time.

14. Install the second Bearing and Housing assembly

(extended side first) onto the Shaft and Flange Assembly

and onto the Bolts.

15. Secure the Bearing assembly to the Base Assembly with

Nuts (1).

• Tighten the Nuts alternately and evenly.

Revision (10-13)

16. Tighten the Nuts on the opposite Bearing alternately

and evenly.

17. Install Retaining Ring (15) onto the Shaft and Riser

Assembly.

18. Install and hold Square Key (4) into the slot of the

Shaft and Flange Assembly.

19. Slide Spring Arbor (25) [flat side first] onto the

Shaft and onto the Key.

20. Install Retaining Ring (15) onto the Shaft and Flange

Assembly.

Power Spring Assembly and Arms

21. Remove Button Plug (14) from the Power Spring

Assembly.

• Use a blunt tool from behind the Plug to "pop" it

from the case.

HINT: Orient the hook on the Power

Spring's inner coil to properly engage the

recess in the Arbor. Lift and center the coil

within the case during installation.

22. Install the Power Spring Assembly onto the Arbor.

• Make sure the end of the power spring properly

engages the Arbor.

IMPORTANT: Use care not to damage the

gasket.

23. Align the bolt holes in the Power Spring Assembly

with the Base Assembly.

24. Secure the Power Spring Assembly to the Base

Assembly with Screws (5).

25. Install the Button Plug into the case of the Power

Spring Assembly.

NOTE: The Hose Guide Arms can attach

to the Base Assembly in five (5) different

positions. Select the required relationship

of the Guide to the mounting plate of the

Base Assembly.

26. Secure Long Arm (33) to the Base Assembly with

Nuts (12).

• Do not tighten the Nuts at this time.

27. Secure Short Arm (13) to the Power Spring

Assembly with Screws (5) and Nuts (1) as required.

• Do not tighten the Screws at this time.

High-Capacity Reel

Alemite LLC