ASI 0165 Montageschablone - Seite 2

Blättern Sie online oder laden Sie pdf Montageschablone für Trockner ASI 0165 herunter. ASI 0165 2 Seiten.

Seite drucken

Recommended mounting heights

- from bottom edge of dryer above finished floor (AFF)

Men

50"

(1270 mm)

Women

47"

(1194 mm)

Children 4-7 years

35"

(889 mm)

Children 8-10 years

39"

(991 mm)

Children 11-13 years

43"

(1092 mm)

Children 14-16 years

47"

(1194 mm)

Handicaped

40"

(1016 mm)

- IMPORTANT - READ COMPLETELY BEFORE

Installation

STARTING INSTALLATION PROCEDURE

1. Make sure power supply breaker is switched off. Installation must be carried out in accordance

with the current edition of the local wiring regulations code having jurisdiction. Installation should

be performed only by a qualified electrician.

2. Place template against wall at desired height (see mounting height recommendations) and mark

locations of 4 mounting holes and wire service entry at knockout (KO) location.

Note: For two or more dryers, dryers should be no closer than 24 inches (610 mm) on center.

3. Remove and retain 2 cover screws and cover.

4. For in-wall (concealed) power supply - Provide supply wire to KO location according to local code

and attach securely to chassis at KO with appropriate strain relief connector (not supplied).

5. Attach dryer to wall. For wood wall/studs use ¯1/4 inch (6 mm) screws at length that will ensure

1 inch (25 mm) min. stud penetration. For masonry walls use expansion bolts or anchors for ¯1/4 inch

(6 mm) screws to ensure penetration 1/4 inch (6 mm) deeper than anchor. Shim if necessary to

ensure base plate is flat against wall.

6. Connect supply and ground wires to terminal block where indicated or connect supply wires to terminal

block where indicated and connect ground wire to base plate with ground screw (Connections: A.

Connect the live wire (colored Brown or Black) to the terminal block marked "L1". B. Connect the

neutral wire (colored White or Grey) or connect the second live wire (colored Red or Orange) to the

terminal block marked "N/L2". C. Connect the ground wire (colored green or green and yellow or bare

conductor) to the terminal block marked "

" or to the green screw marked "

neutral wires depend on voltage of supply service and requirements of Building and Electrical Code

having jurisdiction.

7. Replace cover. Do not over-tighten screws.

8. Switch on circuit breaker and test unit operation.

9. Complete and mail registration reply postcard.

Reference ADAAG

AFF (maximum)

Reach LIMIT (unrestricted)

All Approaches

48"

(1219 mm)

"). Colors of live and

Schematic

)

( 2 2 0

/ 3 2 "

8 - 2 1

)

2 0 0

8 " (

7 - 7 /

SEE NOTE 6

Circuit Diagram

The ground wire must be connected

0165/0185/0195 100-240VAC

NOTE

to the dryer's backplate.

0184

277VAC

Service by qualified electrician ONLY.

Thermal Switch 25A

Supply line 75 C requirement.

on Heater element

Do not daisy chain the ground wire.

P/N A0013

Connect to 20A branch circuit ONLY.

(Brown)

0165 P/N A0036

(Blue)

0184/0185/0195 P/N A0019

N/L2

SENSOR

(G/Y)

Transistor power switch

40A P/N A0024

1 2 3 4 5

1 2 3

CIRCUIT BOARD

100-240VAC-P/N A0009

277VAC-P/N A0038

1 2 3

(Black)

(White)

(Blue)

IMPORTANT

USE TEMPLATE

05072041-1

05072041-2

Rev B 30 Aug 07