doona Lab SensAIert Manual de instalación de inicio rápido - Página 14

Navegue en línea o descargue pdf Manual de instalación de inicio rápido para Accesorios para bebés doona Lab SensAIert. doona Lab SensAIert 16 páginas.

Imprimir página

Device reset

To reset the device, overturn SensAlert, open the zip and press the button in the

lower border

on the black box . Press and hold for 10 consecutive seconds.

Wait for the sound and press 3 more times quickly.

If you are the owner of the reset SensAlert, open the app, find the device in

question, press the settings icon and press "remove SensAlert".

Battery

SensAlert is powered by two CR2032 batteries (3 V), compliant with IEC 60086-4

standard. SensAlert's battery level can be monitored through the app. In case

of low level, the user can independently replace the battery. The new battery

must have the same characteristics and respect the correct polarity. To

replace the battery, the user must open the hinge and unscrew the small screw

located in the lower internal part. Flip the SensAlert over and lift the small black

lid. Replace the two batteries, paying attention to respect the correct polarity.

Close by repeating the operations in reverse order.

Lithium metal batteries

operating temperature: -20 to +60 C

EU Battery Directive 2006/66/EC, 2013/56/EU)

UN3091, Class9 (for the Air transport by PI969 Section II)

IATA Dangerous Goods Regulations Edition 62 (IATA DGR)

During the transportation of a large amount of batteries by ship, trailer or

railway, do not leave them in the places of high temperatures and do not allow

them to be exposed to condensation.

Warning:

Do not use different types of batteries as they can make the baby

safety device ineffective.

Do not let water penetrate into packaging boxes during their storage and

transportation.

Do not store the battery in places of high temperature or under direct sunlight.

Please also avoid places of high humidity.

Be sure not to expose the battery to condensation, extreme pressure, rain or

frozen conditions.

Do not short-circuit, deform, throw into fire or disassemble.

Charge according to the conditions specified.

Do not solder directly onto batteries.

Insert the battery correctly in electrical equipment.

Do not mix different type of batteries.

Do not ingest the battery, chemical burn hazard.

WARNING!

Warning:

This product contains a Button or Coin Cell Battery. A swallowed Button

or Coin Cell Battery can cause internal chemical burns in as little as two hours

and lead to death. Dispose of used batteries immediately. Keep new and used

batteries away from children. If you think batteries might have been swallowed

or placed inside any part of the body, seek immediate medical attention. the

product contains small parts or other characteristics that makes it unsuitable for

children. Serious injuries or death may occur.

Declaration of conformity

With the document herein, Doona warrants that SensAlert complies with the

seven essential requirements and the other relevant provisions established by

the 2014/53/EU Directive. According to the European Commission decision No.

2000/299/EC dated 04/06/2000, the frequency band used by this product is

harmonized throughout the EU countries. Therefore, this is a class 1 product and

can be freely used in all countries of the European Community.

Model: SensAlert

Contains FCC ID:QOQ-BGM220S2

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must ac-

cept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-

sonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT: Changes or modifications not expressly approved by Doona could void the

user's authority to operate the equipment.

Industry Canada Statement

Contains IC:5123A-BGM220S2

This device complies with Idustry Canada license exempt RSS standard(s).

Operation is subject to the following two conditions:

1. this device may not cause interference, and 2. this device must accept any interference,

including interference that may cause undesired operation of the device.

THIS PRODUCT

IS IN COMPLIANCE WITH

EU DIRECTIVE 2012/19/EC.

separate disposal from domestic waste, must be taken to a differential waste collection center

for electric and electronic equipment or returned to the seller when a new, equivalent piece

of equipment is purchased. The user is responsible for handing over the piece of equipment to

the appropriate differentiating center at the end of its life cycle. Suitable differentiated waste

collection in prevision of the re-cycling of the decommissioned equipment and eco-compa-

tible disposal contributes to preventing possible negative consequences to the environment

and health and encourages the recycling of materials used to manufacture the product.

Unauthorized disposal of the product by the user entails administrative penalties pursuant to

Legislative Decree no. 22/1997 6 (Art.50 et seq. of Legislative Decree 22/97). For more infor-

mation on the collection systems available, please contact your local waste disposal service

or the shop where you purchased the product.

COMPLIANCE WITH EU DIRECTIVE

2006/66/EC AND SUBSEQUENT

AMENDMENTS.

the end of its useful life, these items need to be treated separately from household waste.

They must not be

disposed of as urban waste, but transferred to a waste disposal center for separate collection,

or returned to the retailer when purchasing new rechargeable and non-rechargeable batte-

ries. The possible chemical symbol Hg, Cd, Pb, placed under the crossed-out bin indicates the

type of substance contained in the battery, Hg = Mercury, Cd = Cadmium, Pb = Lead. Users

are responsible for providing the end-of-life batteries to the appropriate collection facilities in

order to facilitate treatment and recycling. The adequate separate collection for the subse-

quent forwarding of dead batteries for recycling, processing and environmentally compatible

disposal, helps to avoid possible negative effects on the environment and on human health

and promotes the recycling of substances contained in the battery. Unauthorized disposal

of the product by the user involves damage to the environment and human health. For more

information on the collection systems available, please contact your local waste disposal

service or the shop where you purchased the product.

ISO 7000-1641 (2004-01).

To identify the location where the operator's manual is stored or to identify information

that relates to the operating instructions. To indicate that the operating instructions

should be considered when operating the device or control close to where the symbol

is placed.

ISO 7000-0434 (2004-01)

To indicate that caution is necessary when operating the device or control close to

where the symbol is placed. To indicate that the current situation needs operator awa-

reness or operator action in order to avoid undesirable consequences.

The symbol of the crossed bin

shown on the equipment indi-

cates that, at the end of its life

cycle, the product requiring

T h e s y m b o l o f t h e c r o s -

sed - out bin shown on the

batteries or on the product

packaging indicates that, at