AMERITRON AL-1500 Manual de instrucciones - Página 3
Navegue en línea o descargue pdf Manual de instrucciones para Amplificador AMERITRON AL-1500. AMERITRON AL-1500 16 páginas. Full power linear amplifier
Imprimir página
FEATURES
1. High performance tube: the AL-1500 uses a single rugged
3CX1500A7/8877 tube.
2. High power gain:
the 3CX1500A7/8877 features high
power gain. As little as 65 watts of drive power will pr
vide 1500 watts of output power.
3. SSB/CW switch: the bias voltage is switched to provide
the best linearity on SSB or the lowest dissipation on CW
operation.
4. ALC Indicator: the drive level is detected to provide a
control voltage for the exciter. ALC prevents overdriving
of the linear and reduces distortion from excessive drive
power.
5. Vernier Plate and Load Adjustments: both tuning controls
have vernier 6:1 reduction drives for smooth tuning.
6. Two Illuminated Panel Meters: the AL-1500 has two il-
luminated panel meters. The Grid Current meter provides
a continuous reading of grid current and indicates
TECHNICAL SPECIFICATIONS AL-1500
Input:
Circuit type: Pi-network, slug tuned coils Maximum VSWR
at resonance:
Minimum 2:1 VSWR bandwidth: 20% of
1.3:1
center frequency Maximum drive power permissable: 100
watts Typical drive for full power output:
Output:
Circuit type: Pi-L, Pi
hour continuous carrier: 1500 watts 30 second
/2
continuous carrier: 2500 watts
1/2 hour PEP two-tone test: 2500 watts plus 30 second
PEP two-tone test: 2500 watts plus
Power Supply:
Circuit type: full wave bridge, capacitor input
No load voltage: 3600 V
Full load voltage: 3300 V
Full load current: 1 amp
Regulation: 10% typical
Transformer: 34 lbs., hypersil
Capacitors: 26 mfd total, computer grade
Maximum draw at rated output: 15 amps at 240V AC 50/60 Hz
Tube:
Type:(1) 3CX1500A7/8877
Continuous dissipation: 1500 Watts
Warm-up time: 180 seconds
proper operation of the amplifier. The other meter reads
Plate Voltage (HV), Plate Current (IP), Peak RF
(PO) and ALC.
7. Operate/Standby Switch: filament and plate voltages are
8.12 Volt Auxiliary Jack: 12 volts at 100 mA is provided for
9. XMT Indicator LED: provides a front panel indication of
10. Grid Overload Circuit: this amplifier has a circuit that
protects the tube from excessive grid current. If 175 mA of
peak grid current is reached the "OPR" LED will no longer
light and the amplifier will go into a bypass condition. This
overload condition can be reset by momentarily putting the
STBY/OPR switch in the STBY position.
Caution: This amplifier must be disconnected from the power
mains before removing the cover. See the warning on page
10.
Metering:
Multimeter: Plate current, plate voltage, drive/ALC, power
output (PEP watts)
Grid: Grid current
ALC: Negative going, 0-20V, adjustable, phono jack
watts
65
Efficiency CW: 65% typical
Efficiency SSB (envelope crest): 62%
MARS/WARC: yes, set to nearest highest amateur band
Keying: Requires relay closure or sinking to ground of
DC at 100 mA, phono jack
RF Connectors: S0239
Line Connector: NEMA 6-15P, 240V style
Dimensions: 18
Weight: 77 lbs.
Frequency Coverage: (AL-1500)-1.8, 3.5, 7, 14, 18 and 21
MHz. User modified models cover 24 and 28 MHz. (AL-
1500X/J) Export models-1.8, 3.5,7, 14, 18, 21, 24 and 28
MHz.
Third Order IMD at Rated Output: -36 dB
maintained while allowing the amplifier to be bypassed
for "barefoot" operation.
accessories such as the ATR-15 Antenna tuner.
proper amplifier keying by the exciter during operation.
D x 17 W x 10 H
1/2
Watts
t 12V