Astro Pneumatic Tool 30570 Manual - Página 6

Navegue en línea o descargue pdf Manual para Sander Astro Pneumatic Tool 30570. Astro Pneumatic Tool 30570 9 páginas. 20v 7" brushless variable speed rotary polisher w/ 2 batteries

Imprimir página

30570

Model:

f) Threaded mounting of accessories must

match the polisher spindle thread. For

accessories mounted by flanges, the arbor

hole of the accessory must fit the locating

diameter of the flange. Accessories that do

not match the mounting hardware of the power

tool will run out of balance, vibrate excessively

and may cause loss of control.

g) Do not use a damaged accessory. Before

each use, inspect the accessory such as

abrasive wheels for chips and cracks. If

power tool or accessory is dropped, inspect

for damage or install an undamaged

accessory. After inspecting and installing an

accessory, position yourself and bystanders

away from the plane of the rotating accessory

and run the power tool at maximum no-load

speed for one minute. Damaged accessories

will normally break apart during this test time.

Warning: If battery pack case is cracked

or damaged, do not insert into charger. Danger

of electric shock, electrocution and leakage.

h) Wear personal protective equipment.

Depending on application use face shield,

safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping flying debris generated

by various operations. The dust mask or

respirator must be capable of filtrating particles

generated by your operation. Prolonged exposure

to high intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken accessory

may fly away and cause injury beyond immediate

area of operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an operation

where the polishing accessory may contact

hidden wiring or its own cord. Polishing

accessory contacting a "live" wire may make

exposed metal parts of the power tool "live and

shock the operator.

k) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grab the surface and

pull the power tool out of your control.

Product Type:

20V 7" BRUSHLESS VARIABLE SPEED

ROTARY POLISHER W/ 2 BATTERIES

l) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

m) Regularly clean the power tool's air vents.

The motor's fan will draw the dust inside the

housing and excessive accumulation of

powdered metal may cause electrical hazards.

n) Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or

snapping rotating wheel, backing pad, brush or

any other accessory.

Pinching or snapping causes rapid stalling of the

rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory's rotation at the point of

the binding.

For example, if an abrasive wheel is snapping or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction

of the wheel's movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control

over kickback or torque reaction during

start-up. The operator can control torque

reactions or kickback forces, if proper

precautions are taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over

your hand.

c) Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction

opposite to the wheel's movement at the point

of snapping.

Page 6