Alemlube G10040N Manual técnico del propietario - Página 4
Navegue en línea o descargue pdf Manual técnico del propietario para Herramientas Alemlube G10040N. Alemlube G10040N 7 páginas. 18v lithium-ion cordless grease gun el-series
Imprimir página
HOW TO INSTALL A GREASE CARTRIDGE
REMOVING EMPTY GREASE CARTRIDGE
1) Pull back on the follower handle until the follower rod is fully extended and latch the follower rod groove
into the slot on the barrel end cap of the Grease Barrel.
2) Unscrew the grease barrel assembly from the gun.
3) Carefully release the follower handle to eject the empty cartridge from container barrel.
INSTALLING GREASE CARTRIDGE
1) Remove the plastic cap from the grease cartridge and insert cartridge into the grease gun barrel.
2) Remove the pull tab from grease cartridge and screw grease barrel into pump assembly.
3) Release follower rod from slot to allow it to go forward. Purge air from pump. See air purging instructions.
TO CONVERT GUN TO ALLOW FILLING FROM BULK CONTAINER OR FILLER PUMP
1) Unscrew the grease barrel assembly cap from the grease barrel assembly. Pull on the follower handle to extract
the follower and spring from the grease barrel assembly.
2) Grasp follower between thumb and forefinger and flip the follower lip from rear facing to the front facing.
3) Re-assemble the follower into the grease barrel assembly and position with the follower handle so that the
grease barrel assembly cap can be tightened onto the container barrel.
TO FILL THE GUN FROM A BULK CONTAINER
1) Remove grease barrel from the gun.
2) Insert the open end of the grease barrel assembly into lubricant.
Slowly pull the follower handle back while pushing the grease barrel assembly deeper into the lubricant to prevent
air pockets from being pulled into the grease barrel assembly.
3) When the follower rod is fully extended, pull it sideways to latch the rod groove into the keyhole slot in the
grease barrel assembly cap.
4) Turn the grease barrel into the gun and release the follower rod from the slot on the end cap of the barrel to
allow the follower rod go forward.
5) Clean any excess grease off the gun body.
TO FILL THE GUN WITH A FILLER PUMP
Engage the follower rod with the follower by rotating the follower handle. Insert the gun filler nipple into the filler pump
socket. Operate the filler pump to fill the container. When the follower rod groove is exposed, the grease barrel
assembly is filled. The follower rod will be extended approximately 8 inches (20 cm). Disengage the follower rod from
the follower by rotating the follower handle. Push the follower rod into the grease barrel assembly.
TO EXPEL AIR POCKETS
1) Free the follower rod from the grease barrel assembly cap and depress the vent valve while pushing
the follower rod forward.
2) Squeeze the trigger several times to operate gun until trapped air is expelled.
Push the follower rod into the grease barrel assembly.
INSPECTION, MAINTENANCE AND CLEANING
1. WARNING: Make sure the switch is in its off position, and unplug the charger from its electrical outlet before
performing any inspection, maintenance, or cleaning.
2. BEFORE EACH USE: check the general condition of the grease gun. Check for misalignment or binding of
moving parts, cracked or broken parts, leaking battery, damaged hose, and any other condition that may affect its
safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use.
Do not use damaged equipment.
3. BATTERY PRECAUTIONS: Never burn Batteries, as they can explode in a fire. Do not charge leaking batteries.
Only a qualified service technician should perform maintenance on the battery. Contact local solid waste authorities
for instructions on correct disposal or recycling of the battery.
4. DAILY: Use a soft, dry cloth, remove all dirt, grease, and debris from the exterior of the grease gun.
Do not use solvents to clean the grease gun.
5. WHEN STORING: Always remove the battery from the grease gun.
Keep the grease gun and its accessories in a clean, dry location and out of the reach of children.
NSW
QLD/PNG
TEL: (02) 9939 0711
TEL: (07) 3204 9166
FAX: (02) 9939 0411
FAX: (07) 3204 1224
Visit our website at
VIC/TAS
WA
TEL: (03) 8787 8288
TEL: (08) 9209 3066
FAX: (03) 8787 8266
FAX: (08) 9209 3933
www.alemlube.com.au
SA/NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
Email - [email protected]
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008
4