Electrolux B 522 M Manual de instrucciones - Página 7

Navegue en línea o descargue pdf Manual de instrucciones para Congelador Electrolux B 522 M. Electrolux B 522 M 10 páginas. Upright freezer
También para Electrolux B 522 M: Manual del usuario (8 páginas)

Imprimir página

Assemble the correct guard to suit the kind of

blade or nylon string head to be used (See sec-

tion: SAFETY GUARD ASSEMBLY).

1) Assemble blade as illustrated:

a) Flange guard - b) Upper cap with blade

centering - c) Blade with text and directional

arrow facing upwards - d) Lower washer - e)

Fixed mower gauge - f) Blade locking screw

(length mm 16).

2) If you want to assemble the rotating mower

gauge,proceed as illustrated:

a) Flange guard - b) Upper cap with blade

centering - c) Blade with text and directional

arrow facing upwards - d) Lower washer - e)

Spacer - f) Rotating mower gauge - g) Blade

locking screw (length mm 34,5).

Replace the blade attachment bolt if damaged

in any way.

3) Make sure that the blade bore opening fits per-

fectly around the centering collar on the upper

cap.

1) DOUBLE HANDLE

Handle (A) can be adjusted for individual

operator comfort by swivelling it forwards or

backwards. To do this, loosen button (C),

position the handle for maximum comfort,

then tighten button (C) securely. Clip the

suspension harness hook into one of the

holes on the top side of the shaft support to

achieve the best balance according to the

type of work to be undertaken.

WARNING: First read sections: SAFETY RULES,

SAFETY USAGE and SYMBOLS.

STARTING A COLD ENGINE

1) Position the on/off switch to the I (ON)

position, away from the «STOP» position.

2) Rotate the choke lever in the direction illustrated

by the arrows. This engages the fast idle system.

3) Squeeze the primer bulb (C) several times

until you see fuel begin to return back through

the tube (D) towards the fuel tank. Push the

decompression valve (B) down if your models

is fitted with one. Pull the starter handle until

the engine starts.

4) Hold the machine safely and allow the engine

to run for a few seconds. Grip the control han-

F. Blade and nylon string head assembly

G. Handle assembly

H. Starting and stopping the engine

Tighten counterclockwise.

While tightening, the blade assembly can be

held fast by inserting the wrench or the screw-

driver supplied into the cap and gearcase

holes.

To do this, rotate the cap intil the two holes

coincide.

4) Assemble nylon string head as illustrated:

a) Flange guard - b) Upper cap - c) Guard d)

Nylon string head

Tighten counterclockwise.

5) While tightening, the head assembly can be

held fast by inserting the wrench or the screw-

driver supplied into the holes as already shown

for blade assembly.

WARNING: Do not use the guard for the nylon

string head (18) when using a metal blade.

NB: Handle assembly (A) can be folded

parallel to the shaft to facilitate

transportation or storage. To do this,

loosen knob (C), twist support (B) 90° in a

clockwise direction, fold the handle (A)

into the required position and then tighten

knob (C).

2) DOUBLE HANDLE

Adjust and secure double hand clamp by tight-

ening the screws.

dle firmly, pushing down on the safety trigger

(S) and then squeezing the accelerator trigger

(A). This action automatically releases the

spring loaded choke lever (E) disengaging the

fast idle system.

WARNING: The fast idle system does cause the

cutting attachment to rotate when engaged.

STARTING A WARM ENGINE

Position the on/off switch to the I (ON) position.

Squeeze the primer bulb (C) several times until

you see fuel begin to return back through tube

(D) to the fuel tank. Pull the starter handle until

the engine runs.

HOT ENGINE STARTING WITH

1) STOP switch on START position I. Trigger on

ENGLISH - 5