Atlas 100 Series Manual - Página 4

Navegue en línea o descargue pdf Manual para Bastidores y soportes Atlas 100 Series. Atlas 100 Series 12 páginas. Floor-standing cabinets
También para Atlas 100 Series: Instrucciones de instalación (1 páginas)

Imprimir página

100, 200, 500, 700, & FMA Series

7. Initial Rear Door Setup

Initial Door Setup:

DID YOU KNOW? The rear flush door (typically supplied with most cabinets) may be hung left or

NOTE: The rear flush door (typically supplied with most

right-hinged as required by the final installation. The key lock rotation may also be changed.

cabinets) may be hung left or right-opening as required by the

NOTE: The flush rear door may not be installed on the front of the cabinet.

final installation. However, the rear door may not be installed

on the front of the cabinet.

NOTE: Interference could exist between racked-equipment and door. See Initial Rail Setup section

before proceeding.

Remove rear door by pulling the spring-loaded Cane Bolts towards the

a. Remove rear door by pulling the spring-loaded Cane Bolts towards the center of the door.

center of the door.

Be sure nylon gap washer located at the bottom of the door is retained.

b. Be sure nylon gap washer located at the bottom of the door is retained.

Flip door as required.

c. Flip door as required.

Install the door into position with the nylon gap washer located at the

bottom of the door.

d. Install the door into position with the nylon gap washer located at the bottom of the door.

Be sure spring-loaded Cane Bolts actuate to their outward position.

e. Be sure spring-loaded Cane Bolts actuate to their outward position.

f. If required, the rotation and lock position may be changed to suit the user:

Floor Installation:

Open the door.

ii.

Remove the bolt in the back of the lock.

NOTE: It is easiest to install cabinet before loading. Otherwise,

be sure adequate room exists to get tooling into the bottom

iii. Carefully remove the lock cam and lock washer.

areas of the cabinet.

iv. Behind the lock cam is a special 90° washer. This washer has a section removed and controls the lock and unlock orientations by

engaging on a protrusion on the lock body. Carefully remove this special 90° washer.

Always install cabinet on a level surface and suitably anchored in all (4) corners.

All cabinets have (4) corner holes at ½" diameter will each accommodate a 3/8" to 7/16" diameter bolt passing through the

Insert the key into the lock and orient to the desired locking position.

steel bottom panel that is spaced 2" to 3" from the floor or directly on the floor (depending on model). The 700 Series

vi. Replace the special 90° washer and then turn the key to the unlocked position. Repeat using different orientations until the desired

cabinets also have an additional (2) holes located in each bottom corner. FMA Series cabinets have only (2) holes in

locking and unlocking orientations are met. Note: The washer can be flipped if needed.

each corner.

vii. Replace the lock cam, lock washer and bolt to match the desired locking and unlocking orientations.

8. Front Door Installation (purchased separately)

DID YOU KNOW? The optional front door (purchased separately) may be hung left or right- hinged

as required by the final installation. The key lock rotation may also be changed.

NOTE: Interference could exist between racked-equipment and door. See Initial Rail Setup section

before proceeding.

a. Orient the door, as it will be mounted on the cabinet. The hinge side will be opposite

from the handle and lock.

b. On the hinge side, remove the 4 caps protecting the door installation points on the cabinet.

These may be discarded.

c. On the cabinet, mount the male hinge with the pins facing up. Use the two longer

10-32 x .75" cap screws found in the hardware bag to mount each male hinge. Install using

⁄

hex driver key.

d. Install the two screw covers provided in the hardware bag on each male hinge.

e. Eight (8) holes are located on the hinge side of the door. There are four (4) holes near the

top and four (4) holes near the bottom. Mount the female hinge on the door using the

shorter 10-32 x .25" cap screws provided in the hardware bag. The hinge will mount on the

upper two (2) holes of the four (4) holes found near the top. The second hinge will mount

on the upper two (2) holes of the four (4) holes found near the bottom. In each case, the

female hinge will be mounted with the hinge-hole facing down. Due to the limited space, it

is best to use a L-Shaped

f. Mount door to cabinet.

1601 JACK MCKAY BLVD.

ENNIS, TEXAS 75119 U.S.A.

Floor-Standing Cabinets

700 Series Bottom Corner

⁄

hex key.

FMA Bottom Corner

To Remove

100, 200, and 500 Series

Bottom Corner

TELEPHONE: (800) 876-3333

FAX: (800) 765-3435

4/12

AtlasSound.com