Alert 500S LCD Manual del usuario - Página 7
Navegue en línea o descargue pdf Manual del usuario para Alarma de coche Alert 500S LCD. Alert 500S LCD 13 páginas.
Imprimir páginaM. PANIC FUNCTION: (See Alarm Feature V - 4 Programming)
The transmitter can be used as a remote panic switch to manually trigger
the alarm in case emergency.
✱
. Press and hold the
button for second. The alarm will immediately
sound.
. During panic mode, the normal function of this transmitter button will
be suspended. The and buttons can be used to lock and unlock
the doors (if the option is installed), however once the button is
pressed, the vehicle's starter disable device, (where installed) will be
disabled allowing the vehicle to start.
✱
. To stop the alarm, press and hold the
✱
if any transmitter button other than
mode will be turned off immediately.
4. If the button is not pressed, the alarm will automatically stop after 0 seconds.
N. TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
. Light impacts will trigger the warn-away signal. A long chirp from siren/horn.
. Heavy impacts / Doors open / Hood open / Trunk open / Turn on the ignition key will trigger the
programmed sequence.
The starter disable relay (if installed) prevents the vehicle's starter from cranking. The siren, horn,
parking lights, and dome light will turn on to alert you of an intrusion for 30 seconds. Then it will
stop and automatic reset and re-arm. If the one of sensors or detectors still activate the alarm
system, it will sound a maximum of 6 times of 0 seconds cycles.
Trunk/Hood
doors Trigger
Trigger
button on the transmitter again for seconds. Also
or or button is pressed and released, the panic
Shock Sensor
Warn-away
Ignition Trigger
Trigger
STOp THE MELOdY SOUNd ONLY: While triggering the alarm the LCD screen will alert user
through melody sound and flashing trigger icon, press any button on the LCD remote transceiver
to stop melody sound only
CLEAr THE FLASHING ICON ANd MELOdY SOUNd: While triggering the alarm the LCD screen
will alert user through melody sound and flashing trigger icon, press the F button times within
seconds will clear the flash icon and stop melody sound on the LCD screen transceiver.
NOISE ABATEMENT CIrCUIT: Your system has " Noise Abatement Circuit". It prevents annoying
repetitive trigger sequences due to faulty door pin switches or environmental condition such as
thunder, jackhammers airport noise, etc.
Here's how " Noise Abatement Circuit" works: The alarm triggers five times. Each time, the same
sensor or switch is triggering the alarm. " Noise Abatement Circuit" will interpret this pattern of
triggers as false alarm. After the fifth trigger, " Noise Abatement Circuit" ignores, or by pass, that
sensor or switch until the other sensor or switch is triggered.
Doors (Hood/Trunk) are covered by " Noise Abatement Circuit" differently: If the alarm is triggered
by an open door for six full cycles (three minutes), the doors will be bypassed until the trigger
ceases.
O. ANTI CAR-JACKING:
Warning: If you don't need the anti car- jacking function in this alarm system, be sure to set car
jacking feature " OFF". This system is default setting all car-jacking " OFF". (See Alarm Feature I - 4
Programming.)
ACTIVE ANTI CAr JACKING:
. Press and hold the transmitter and buttons at the same time for seconds while the vehicle's
ignition is ON. The parking lights will turns on for .5 seconds to indicate the system enters the
car-jacking mode.
Trigger
. Once the system in car-jacking mode, If you are forced from the vehicle, the system will be
trigger when the door is opened and closed while the ignition is " ON".
pASSIVE ANTI CAr- JACKING:
. Turn the ignition switch to " ON" position; the system enters the car-jacking mode.