Bose ShowMatch SM10 Manual de uso y aplicación - Página 14
Navegue en línea o descargue pdf Manual de uso y aplicación para Sistema de altavoces Bose ShowMatch SM10. Bose ShowMatch SM10 28 páginas. Deltaq array loudspeakers
También para Bose ShowMatch SM10: Manuales de instalación y seguridad (16 páginas)
Imprimir página
2
1
3
Initial System Loudspeaker Connections
Loudspeakers are connected via the Loudspeaker Connection Panel. The following diagram details the connections
between the ShowMatch Tour Rack, arrays and subs based on the pre-loaded configuration.
Loudspeaker connection panel
Amp 1
Ch 1+2
All Ch Ch 3+4
Ch 1 Ch 2 Ch 3 Ch 4
LEFT
SM5 100°
SM5 100°
SM5 100°
SM5 100°
SM10 100°
SM10 100°
SMS118
SMS118
SMS118
SMS118
24
1 Virtual Representation of ShowMatch
Tour Rack.
2 Virtual Loudspeaker Group — each array
and sub section is grouped and includes an
advanced group control for Polarity, EQ, Delay
and Gain of this section.
3 Advanced Group Control for subs, arrays
and full system. Each contains Polarity, EQ,
Delay and Gain.
Amp 2
Amp 3
Ch 1+2
All Ch Ch 3+4
Ch 1+2
All Ch Ch 3+4
Ch 1 Ch 2 Ch 3 Ch 4
Ch 1 Ch 2 Ch 3 Ch 4
RIGHT
SM5 100°
SM5 100°
SM5 100°
SM5 100°
SM10 100°
SM10 100°
SMS118
SMS118
SMS118
SMS118
Input Connections
AES Inputs — Two AES pairs (1/2 and 3/4) are provided for connection of external AES devices. Each input pair is
transformer-isolated, electronically re-clocked and buffered to the AES inputs of the amplifiers.
Two transformer-isolated outputs are provided for linking of AES signals to another device in the ShowMatch
Tour Rack.
Analog Inputs — Four analog inputs and four parallel link outputs are provided for connection of external analog
devices. The inputs are wired to the analog inputs of the amplifiers.
Dante Network (primary/secondary) — Neutrik EtherCON RJ45 connectors are wired using shielded cable to the
Cisco® Network switch where they are distributed to the amplifiers. Output connections are provided to link multiple
ShowMatch Tour Rack units.
Loudspeaker Connections
The Loudspeaker Connection Panel is divided into three identical sections, one for each amplifier.
Loudspeaker Outputs — Each amplifier output section is wired in parallel to provide flexibility in system configuration
wiring. Each output connection contains the following connections:
1 – NL8 – Carries all Output Channels
1 – NL4 – Carries Channels 1+2
1 – NL4 – Carries Channels 3+4
4 – NL4 – Each carries a single amplifier channel
The following describes the channel connector wiring and maximum channel loading:
Single Channel Connection
Connector
Channel
NL4
1
NL4
2
NL4
3
NL4
4
Max Loading per Connection
Qty
2
1) Subs run in parallel, requires jumper
to second unit
PRO.BOSE.COM
PRO.BOSE.COM
Channel Pair Connection
Pin Out
Connector
Channel
Pin Out
1±
1±
NL4
1
1±
2±
1±
1±
3
NL4
4
1±
2±
Max Loading per Connection
Type
Qty
Type
ShowMatch Module
SMS118
1
3
(bi-amped)
4
SMS118
1,2
1) Requires breakout cable
2) Subs run in parallel, requires jumper
to second unit
Input Panel
Loudspeaker Connection Panel
Quad Channel Connection
Channel
Connector
Pin Out
1±
1
2±
2
NL8
3
3±
4
4±
Max Loading per Connection
Qty
Type
ShowMatch Module
6
(bi-amped)
8
SMS118
1,2
1) Requires breakout cable
2) Subs run in parallel, requires jumper
to second unit
25