Auber Instruments DSPR300 Manual de instrucciones - Página 4

Navegue en línea o descargue pdf Manual de instrucciones para Controlador Auber Instruments DSPR300. Auber Instruments DSPR300 12 páginas.

Imprimir página
AUBER INSTRUMENTS
Note 3. Temperature unit setting: C-F
C-F determines the temperature unit. It can be set to C (Celsius, ˚C) or F
(Fahrenheit, ˚F).
goto
syst
Knob
tf
Timer function
on
Knob
Timer
tdir
counting
dn
direction
Knob
Temperature
pb
reading offset
0
Knob
Temp. display
C-f
unit
f
Knob
Relay 1
rl1
mode
off
Knob
Logic mode
lgc1
Rl-c
for relay 1
Knob
Latching or
lat1
pulse action
n
selection for
relay 1
Relay 1
mode
Figure 6. Flow chart of setting system parameters.
6.2 Mashing Parameters
Table 2. Mashing parameters.
Mashing Mode Parameters
Display
Code
Description
Mashing time set
t
t
value
Mashing timer start
tSP
tSP
temp.
Mashing alarm set
ALH
ALH
temp.
Mashing ending
EO
EO
options
oScr
Overshoot correction
oScr
AttE
Attenuation constant
AttE
2021.05
Press
80
End
100
Press
Knob
key
Function Key
off
Press
Knob
Alarm
sil2
suppression
n
for relay 2
Press
Knob
Latching or
pulse action
lat2
selection for
n
relay 2
Press
Knob
Logic mode
lgc2
for relay 2
Rl-c
Press
Knob
rl2
Relay 2 mode
off
Press
Knob
sil1
Knob Press
n
Alarm
suppression
for relay 1
Initial
Setting Range
Setting
00:00~99:59
1:00
(hour: minute)
-999~+9999 ° C
151
or ° F
-999~+9999 ° C
150
or ° F
ON, OFF
OFF
-50~+50
0
-2~+2
0
Press
Press
Press
Press
Press
Press
Figure 7. Flow chart of setting mashing parameters.
Note 6: Timer Function: t, tSP, EO
This timer function allows the controller to show the mashing time. It makes a
beeping sound when timed out and will display the process is ended. It can also
automatically shut off the controller's power output after time out. The time
duration is set by the t parameter for mashing mode. The unit is hour: minutes.
When timer function is enabled, the timer counting will be started by timer start
temperature, tSP. When temperature reaches timer start temperature, the timer
starts to count. After timer started counting, it will continue even if the
temperature drops below this start temperature. The timer can be reset to start
from beginning again. To reset the timer, press the knob momentarily, the display
Remark
will show rSt on top and "n" at the bottom, rotate the dial clockwise will change
the bottom display to "y". Press the knob again will reset the timer (Figure 4)
After the timer starts, the top display will be switched between the current
Note 6
temperature and current time alternately in every 6 seconds. The temperature
and time display can be easily differentiated with their appearance. The
Note 7
temperature reading has two or three digits. For example, 212 degrees will be
displayed as "212". The timer display has four digits with flashing colon in the
Note 6
middle. For example, "01:20" for 1 hour 20 minutes.
Note 8
When time counting ends, the controller will generate six long beeps. The top
display will switch between the current temperature and "End" alternately. After
timer ends, the power output can be configured either to continue heating, or
shut off. It is controlled by the parameter called ending options, EO. Set it to
ON for continue heating, set it to OFF to turn off the output.
WWW.AUBERINS.COM
P4/9