Auber Instruments SYL-5352PA Manual de instrucciones - Página 2

Navegue en línea o descargue pdf Manual de instrucciones para Controlador Auber Instruments SYL-5352PA. Auber Instruments SYL-5352PA 2 páginas. Usb pid controller

Imprimir página

AUBER INSTRUMENTS

LOOP = 0: By default, program looping is enabled. To disable program looping,

change LOOP to 0.

RUN = 3: By default, this controller is under single step mode. To use ramp soak

feature, set RUN to 3.

5. Wiring and programming example: powder coating/heat treatment oven

An oven needs to heat up to 375° F from ambient in 5 minutes. Then hold the

temperature for 20 minutes. After that, pull in the AL2 relay for 2 minutes. If the

temperature is higher than 450° F, trigger the AL1 relay. This application needs

a controller, a relay/SSR, a thermocouple and a two buzzers with a 12V DC

power source.

a. Wiring

Alarm1

Alarm2

12V

SYL-

5352PA

SYL-5352PA with Solid State Relay solution

Alarm1

Alarm2

12V

SYL-5342PA

SYL-5342PA with 40A contactor solution

b. Parameter setting and program

SSb = 5. Safety start band is set to 5 degree.

LOOP = 0. Program automatically looping is disabled.

ALP = 1. Alarm 1 is set to absolute high alarm.

AL1 = 450. Alarm 1 will be activated when reading temperature is over 450

AL2 = 120. Program ending alarm is set to 120s. Once all the steps have been

executed, alarm 2 will be activated for 120s.

T = 2 or 20. Set cycle time to 2s for SYL-5352PA, and set 20s for SYL-5342PA.

The program:

r01 = 2000, t01 = 0, C01 = 80. Initial step. r01 must be 2000. C01(80F) is ambient

temperature.

r02 = 5, t02 = 20, C02 = 375. Ramp up from 80 to 375 in 5 minutes, then soak

at 375 for 20 minutes.

r03 = 0, t03 = 0, C03 = 0. End of the program. Change all three parameters to 0.

Quick explanation: Cxx is end temperature of that step. rxx is the ramp step timer,

txx is the soak step timer. Every step, controller will run ramp up step at first,

then run soak step.

6. Windows Communication software notes:

2020.10

Heater

SSR

Heater

Contactor

1). Default login password is: admin

2). After you login, for first timer user, please click "Auto Select" on the right top of the

screen. Click "Detect" button on the right, then this software will automatically scan your

connected PID controller. Once finished, you will see SYL-53X2P-S is detected (if you PID

model is SYL-5342P-S/SYL-5342PA/SYL-5352P-S/SYL-5352PA). Then click "Apply"

button. If your software cannot detect this PID, please confirm your computer has the

240V AC

correct driver for this USB adapter (see note in the software zip file) and check the

continuity between your adapter and your PID by using a multimeter.

3). You will see the screenshot information above under "Panel View" on the left top. Click

SET button and you can change all the parameters. If you want to change multiple

parameters, please click "Tab View" button on the top. Then right click the number showing

on the right.

4). Click "Start monitor" on the top and you will see temperature chart under "Graph View".

5). Click "Record" on the top and you can use "Report" or "Backup" / "Restore" functions

later.

6). To edit ramp soak profiles, click "Program" button on the right top.

7. Manual & Download

Operation Manual (Full Version):

SYL-5352PA:

https://bit.ly/5352pmanual

240V AC

Or scan the following QR code by

your smartphone:

Win Software Download Link:

https://bit.ly/AuberPIDWin

Or scan the following QR code by

your smartphone:

WWW.AUBERINS.COM

Operation Manual (Full Version):

SYL-5342PA:

https://bit.ly/5342pmanual

Or scan the following QR code by

your smartphone:

Auber Instruments

5755 North Point Parkway, Suite 99

Alpharetta, GA 30022

www.auberins.com

Email: [email protected]

Tech Support: 770-569-8420

No part of this manual shall be copied,

reproduced, or transmitted in any way without

the prior, written consent of Auber

Instruments. Auber Instruments retains the

exclusive rights to all information included in

this document.

P2/2