Galvamet LINE-UP 240 Vac 50 Hz Instrucciones de instalación, funcionamiento y mantenimiento - Página 5

Navegue en línea o descargue pdf Instrucciones de instalación, funcionamiento y mantenimiento para Campana de ventilación Galvamet LINE-UP 240 Vac 50 Hz. Galvamet LINE-UP 240 Vac 50 Hz 14 páginas.

Imprimir página

OPERATION

The hood is supplied with a multispeed motor.

The hood should be run at low speed under normal conditions and at

higher speeds only when there is a heavy build-up of fumes or odours.

Ideally, the hood should be switched on as soon as cooking is started

and then kept on until all odours have been eliminated.

Remote Control Functions

ON-OFF ASPIRATOR

ON-OFF LIGHTING

INCREASE ASPIRATOR SPEED

DECREASE ASPIRATOR SPEED

When turned on, the aspirator is positioned at the second speed. The

motor speed is indicated by the lighting of the respective green LED

(ref. pos. 1-2-3-4). At the fourth speed (intensive, ref. pos. 4), the LED

flashes and after 5 minutes the motor returns to the third speed

automatically.

Remote control encoding

The supplied remote control is already encoded and can be used from

the beginning for the total control of the hood.

To encode another remote control, hold the button "P" on the hood for 4

seconds until the programming red LED lights up, at this point press

immediately after the On / Off aspirator.

When the red LED turns off, the programming is closed and you cannot

no longer program the remote control.

Safety switch

In case the remote control is lost or out of batteries, the appliance shall

be switched off pushing the "P" button.

Restoring Factory Conditions (Reset)

Hold down the "P" button until the red LED lights up and continue to

press the button without releasing until the LED turns off by itself. At this

point no remote control will be coupled and it will be necessary to pair

one again.

Grease filter maintenance warning

The electronic control report, after 100 hours of operation, with the

flashing of the LEDs, for 30 seconds at shutdown of the hood, the need

for cleaning of the grease filters. To reset the counter, after cleaning the

filters, while the flashing warning press the "+" on the remote control

until shutdown.

MAINTENANCE

Always disconnect the hood from the mains before carrying out any

maintenance or cleaning operation.

All the ordinary and extraordinary maintenance can be performed

without having to remove the hood.

Particular attention should be paid to metal grease filters, which have

the function of retaining the fat particles contained in the vapours. The

metal grease filters must be washed at least every month or, if present

in this model, when indicated by the electronic warning, in hot water and

detergent (even in the dishwasher). Filters may become discoloured

after a few washes. This is normal and does not mean that they must

be replaced. To remove the metal grease filters act on the special

handle (Fig. 10). It is recommended to refit the metal grease filters only

if they are perfectly dry.

WARNING: the grease retained by the metal filters is easily

inflammable. It is therefore necessary to regularly clean the filters

according to the instructions.

The activated carbon filters, if present, have the function of retaining the

smells present in the cooking fumes. The air is released into a purified

environment. The activated carbon filters must not be washed and must

be replaced 3 or 4 times a year in accordance with the use of the hood.

Request the filters from the manufacturer.

To replace the activated carbon filters, remove the steel motor

protection panel, positioned centrally between the metal filters: the

locking is performed with magnetic closures, it is sufficient to exert a

modest manual force, without the aid of tools. At this point the activated

carbon filters can be removed by rotating them about 90 ° with respect

to their position to release them from the interlocking tabs, then

accompanying the filter downwards, without the aid of tools. Fig. 11-12-

13-14.

To reinstall the new activated carbon filters, reverse the operations.

The hood must be cleaned immediately after installation and removal of

the protective in order to eliminate any residual glue or other impurities

of any kind.

The hood must be cleaned frequently both internally and externally (at

least once a month).

Do not allow dirt to accumulate on the outer and inner surfaces of the

hood.

Do not use acid or basic products or abrasive sponges to clean the

outer shell of the hood.

Clean the hood with a sponge dampened with warm water and a

modest amount of neutral soap (for example dish soap) in order to

eliminate any grease particles deposited on it.

Rinse with a damp cloth carefully removing all the soap, following the

satin-finish direction of the steel surface.

Particularly important is the drying especially in the areas where the

water has a high hardness and leaves limestone deposits.

The hood is equipped with LED lighting which, in addition to offering

good lighting and significant energy savings, guarantees an average

duration 10 times longer than traditional lamps. In the event of

replacement, contact the after-sales service.

All ordinary and extraordinary maintenance can be performed without

having to uninstall the hood.