Avantco 177CAG15TG Manual del usuario - Página 5

Navegue en línea o descargue pdf Manual del usuario para Equipamiento alimentario comercial Avantco 177CAG15TG. Avantco 177CAG15TG 15 páginas. Commercial countertop griddles, charbroilers & ranges

Imprimir página

User Manual

Gas Conversion Instructions

The products are produced for the use of natural gas (NG). Then check if the gas used in your region

is compatible with the type of gas for which the product was manufactured. Otherwise, the product

must be converted to be used in propane gas (LPG).

IMPORTANT

TO PERFORM GAS CONVERSION, A LICENSED AND QUALIFIED TECHNICIAN IS

REQUIRED.

After converting the product gas, the pressure

regulator must be converted by inverting the

fitting under the regulator cover. This will require

a reasonable amount of force. Do not remove the

spring. When replacing the cover, make sure the

insert of the socket is facing upwards in the middle

of the spring. As shown in the image on the side.

Then re-attach the pressure regulator to the gas

inlet of the product and apply the "Warning" sticker

for the gas to be used on the front of the unit for

future reference.

COUNTERTOP THERMOSTATIC GAS GRIDDLE

For conversion the following guidelines should be followed:

Close the manual gas valve and disconnect the product

1 .

from the gas network, making sure that there is no leakage.

Then remove the pressure regulator from the gas inlet on the

product to make work easier.

2 .

Remove the manual gas griddle assembly (1) with the help of

two or more people. For this, extreme care must be taken, as

physical injuries or serious damage can occur.

3 .

Carefully pull the wire from the thermostat bulb that is fixed

inside a support welded on the bottom of the plate until it is

loose.

Remove the screws that secure the

4 .

burners(3) to the rear support and pilot

burner support (6) with the aid of the

double screwdriver. Afterwards, remove

the burners from the product.

Remove the burners injectors (4) with

5 .

a 1/2" wrench.

6 . In place of the removed gas injectors (4), place the new injectors that are included with the kit shipped with

7 . Remove the pilot burner nut (7) to change the injector orifice that is inside the nut. The orifice for the

8 . After changing the gas injectors, reassemble your product. Return the burners to their original

9 . After repositioning the thermostat bulb inside the welded support at the bottom of the plate, fit the plate

10 . The following image serves to help identify the components mentioned above.

COUNTERTOP MANUAL GAS GRIDDLE

For conversion the following guidelines should be followed:

1 . Close the manual gas valve and disconnect the product

2 . Remove the manual gas griddle assembly (1) with the help of

3 . Remove the screws that secure the burners (2) to the rear

4 . Remove the injectors (3) with a 1/2" wrench.

5 . In place of the removed gas injectors (3), place the new

6 . Once the gas injectors (3) are changed, reassemble your

www.AvantcoEquipment.com

the product. But first apply some pipe sealant to the valve thread and then screw-in the new injectors to the

correct gas type.

exchange is included in the accessory kit.

configuration, however, now with the new injectors.

assembly back into the product. Replace the panel and secure it with the screws that were removed earlier.

from the gas network, making sure that there is no leakage.

Then remove the pressure regulator from the gas inlet on the

product to make work easier.

two or more people. For this, extreme care must be taken, as

physical injuries or serious damage can occur.

support with the aid of the double screwdriver. Afterwards,

remove the burners from the product.

injectors that are included with 4 the kit shipped with the

product. But first apply some pipe sealant to the valve thread

and then screw-in the new injectors to the correct gas type.

product (4).

User Manual