Kohler 21902T-4-3TR Instrucciones de instalación - Página 2

Navegue en línea o descargue pdf Instrucciones de instalación para Productos de fontanería Kohler 21902T-4-3TR. Kohler 21902T-4-3TR 2 páginas.

Imprimir página
INSTALLATION
2
1
6
3
4
5
7
8
9
15
14
18
12
11
13
17
10
16
①
19
1299774-2A-A
How to Install the Spout
Slide the escutcheon(1) into the bottom of the
spout(2). Insert the spout kit into the mounting
hole of the lavatory with escutcheon.
From underside of the lavatory, place the
washer(3), steel washer(4) and fixing ring(5)
onto the shank(6). Position the faucet. Screw
the fixing ring. Tighten the screws(7) to secure
the spout.
Install the supply tee(8) to the shank and
tighten by the hook(9).
How to Install the Side Bodies and
Handles
Put the threaded rings(10), steel washers(11)
and washers(12) onto the side bodies(13).
Insert the side bodies into the mounting holes
from underside. NOTE: The side body with
red mark should be installed on left. Put the
washers(14) into the groove of the nuts(15).
Thread the nuts onto the side bodies.
Adjust the outlet(16) of side bodies to connect
hoses easily. Secure the threaded rings by
tightening screws(17).
Ensure the valves and handles are in the off
position.
②
Screw the handles(18) onto the nuts. NOTE:
The handle with "H" should be installed on left.
How to Connect the Hoses
Connect the hoses(19) to the supply tees. The
other end of the hoses should be connected
to the outlet of side bodies.
24
INSTALLATION CHECKOUT
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could
adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
2
1299774-2A-A
How to Install the Drain
Remove the locknut(20), plastic washer(21),
rubber gasket(22) and tailpiece(23) from the
drain body. Supply enough tape or sealant to
25
tailpiece thread. Reinstall the tailpiece. Insert
the drain body into the lavatory. Install the
Drain Body
rubber gasket(Tapered side up), plastic
washer and locknut back to the drain body in
turn. Tighten the locknut.
23
NOTE: If needed, apply a ring of plumbers
putty or other sealants around the underside
22
of the drain flange(24), instead of using rubber
washer(25).
21
Do not reposition the drain after the locknut is
20
tightened, or you may break the putty or
sealant seal.
Ensure that all coupling nuts are tight.
Ensure that the handles are in the off position.
Turn on the main water supply and drain, and
check for leaks. Repair as needed.
26
27
Remove the aerator(27) by key(26). Run hot
and cold water through faucet for about one
minute to remove any debris. Check for leaks.
Repair as needed. Remove any debris from
the aerator. Shut off the faucet. Reinstall the
aerator.
28
Replace the Washer and Piston Kit
29
Turn counter-clockwise to remove the
30
stopper(28). Take out washer(29). Replace
with a new one. Turn counter-clockwise to
remove the piston kit(30). Replace with a new
one. Reinstall stopper and washer.
3