Dell N1500 Series Instrucciones de actualización del firmware - Página 8
Navegue en línea o descargue pdf Instrucciones de actualización del firmware para Interruptor Dell N1500 Series. Dell N1500 Series 17 páginas. Emcnetworking switches
- 1. Table of Contents
- 2. Introduction
- 3. Global Support
- 4. Firmware Upgrade Overview
- 5. Firmware Downgrade Overview
- 6. How to Access Serial Console on Dell EMC Networking N1500 Series Switches
- 7. Upgrade Example of Dell EMC Networking N1500 Series Switches
- 8. Upgrade Stack of Dell EMC Networking N1500 Series Switches
- 9. Switch Recovery Procedure
- 10. Switch Recovery Example
- 11. End of Document
Upgrade Dell EMC Networking N1500 Series Switches
Programming controller register
ddr_init2: MemC initialization complete
Validate Shmoo parameters stored in flash ..... OK
Press Ctrl-C to run Shmoo ..... skipped
Restoring Shmoo parameters from flash ..... done
Running simple memory test ..... OK
DeepSleep wakeup: ddr init bypassed 3
DDR Interface Ready
CPLD: addr=0x21, rev=10
Board: L2 48 Port Copper POE+ Switch, X01
DRAM:
1 GiB
NAND:
Micron MT29F1G08ABADA, 128 KiB blocks, 2 KiB pages, 16B OOB, 8-bit
NAND:
chipsize 128 MiB
In:
serial
Out:
serial
Err:
serial
arm_clk=1000MHz, axi_clk=400MHz, apb_clk=100MHz, arm_periph_clk=500MHz
Unlocking L2 Cache ...Done
l2cc_invalidate - Done, i = 981, invway = 0
Net:
Registering eth
Broadcom BCM IPROC Ethernet driver 0.1
Using GMAC0 (0x18022000)
et0: ethHw_chipAttach: Chip ID: 0xdb56; phyaddr: 0x1
ethHw_miiphy_write (addr&f):phyaddr (addr&1f00):bank
ethHw_miiphy_write phyaddr(0x1) bank(0x0) reg(0x0) data(0x2100)
bcmiproc_eth-0
========== relocate address: 0xdff7c000, offset 0xc1f7c000 ==========
boot in 3 s
Creating 1 MTD partitions on "nand0":
0x000000200000-0x000007000000 : "mtd=4"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size:
UBI: logical eraseblock size:
UBI: smallest flash I/O unit:
UBI: VID header offset:
UBI: data offset:
1 ecc_errors after reading 2320800:2320a00
UBI: attached mtd1 to ubi0
UBI: MTD device name:
UBI: MTD device size:
UBI: number of good PEBs:
UBI: number of bad PEBs:
UBI: max. allowed volumes:
UBI: wear-leveling threshold:
UBI: number of internal volumes: 1
UBI: number of user volumes:
UBI: available PEBs:
UBI: total number of reserved PEBs: 872
UBI: number of PEBs reserved for bad PEB handling: 8
UBI: max/mean erase counter: 37/16
UBIFS: recovery needed
UBIFS: recovery deferred
UBIFS: mounted UBI device 0, volume 0, name "fs"
UBIFS: mounted read-only
UBIFS: file system size:
UBIFS: journal size:
131072 bytes (128 KiB)
126976 bytes
2048
2048 (aligned 2048)
4096
"mtd=4"
110 MiB
880
0
128
4096
1
8
107802624 bytes (105276 KiB, 102 MiB, 849 LEBs)
5459968 bytes (5332 KiB, 5 MiB, 43 LEBs)
Page 6