Motorola D1012 Manual del usuario - Página 22

Navegue en línea o descargue pdf Manual del usuario para Teléfono inalámbrico Motorola D1012. Motorola D1012 30 páginas. Motorola d1010 series digital cordless phone with answer machine

Imprimir página
d
m
2. Scroll
to
ANSWER MODE
and press
.
-
The current answer mode is displayed.
u
d
3. Scroll
or
to select
ANSWER & REC
or
ANSWER ONLY
u
d
4. Scroll
or
to display the message type you want:
message or
PREDEFINED
for the pre-recorded message.
m
5. Press
to confirm.
If you select PERSONALIZED, see following paragraph.

Record, play or delete your own outgoing message

Answer & Record invites your callers to leave a message. Answer Only lets callers hear your
announcement but they cannot leave a message.
m
1. Press
scroll to
ANSW MACHINE
and press
u
m
2. Scroll
to
ANSWER MODE
and press
u
d
3. Scroll
or
to select
ANSWER & REC
or
ANSWER ONLY
m
PERSONALIZED
then press
.
m
4.
PLAY
is displayed. Press
.
-
Current message is played back.
d
m
• Scroll
to select
RECORD MESS
– press
m
Speak your message. Press
to end recording.
m
•
DELETE
- press
. The pre-recorded message will be automatically reinstated.
m
5. Press
to confirm.

Answer machine settings

Ring delay

Select the duration of rings before your answer machine picks up the call. Choose from 5/10/15/
20/25/30 seconds or Toll Saver.
NOTE
If Toll Saver is selected, then:
• If you have new messages your phone answers after 10 seconds.
• If there are no new messages it will answer after 20 seconds. So you have the option to hang
up, saving the time and cost of a call.
• If the memory is full, it will answer after 30 seconds in Answer Only mode.
m
u
d
1. Press
scroll
or
to
ANSW MACHINE
d
m
2. Scroll
to
ANSW SETTINGS
and press
m
3.
RING DELAY
is displayed. Press
.
u
d
4. Scroll
or
to select 5/10/15/20/25/30 seconds or
m
5. Press
to confirm.
22
m
and press
.
PERSONALIZED
to set your own recorded
m
.
.
m
u
d
and press
. Use the
or
key to select
. Display shows
RECORDING
and a beep is emitted.
m
and press
.
.
TOLL
SAVER.

Remote access

Remote access allows you to operate your answer machine and listen to your messages by calling
your D1010 from another phone.
The default setting is on.
1. Call your D1010. When you hear your outgoing message, press #.
2. Enter your 4 digit PIN. The default code is 0000.
-
You hear a confirmation beep.
NOTE
Change this code for increased security, see "PIN" on page 19.
3. After entering your PIN as stated above, use the keypad to operate your D1010 answer
machine:
Play messages
Play previous message
Play next message
Delete message playing
Switch answer machine on
Stop playback
Switch answer machine off

Remote Access on/off

m
d
1. Press
, scroll
to
ANSW MACHINE
and press
d
m
2. Scroll
to
ANSW SETTINGS
and press
d
m
3. Scroll
to
REMOTE ACC
and press
.
u
d
4. Scroll
or
to select
ACTIVATED
or DEACTIVATED.
m
5. Press
to confirm.

Call screening

Use your handset or base speaker to hear a caller leaving a message. You can then choose to
ignore the caller or pick up the call.
The default settings are:
• Handset call screening: Off
• Base call screening: On.
At the handset:
1. If you want to interrupt and take the call press
At the base:
1. When a caller is leaving a message, press
caller.
2. To interrupt and take the call on the handset, press
2
1
3
6
7
8
9
m
.
.
<
v
or
+
-
or
to adjust the volume to listen to your
<
v
or
.
Using your Answer machine