Air Design CSV44N Manuel d'installation, d'utilisation et d'entretien - Page 14

Parcourez en ligne ou téléchargez le pdf Manuel d'installation, d'utilisation et d'entretien pour {nom_de_la_catégorie} Air Design CSV44N. Air Design CSV44N 19 pages. Water cassettes csvn series; hcvn series

Imprimer la page
THE INFRARED REMOTE CONTROLLER
8
7
1
9
6
11
2
1
Turns the cassette ON or OFF.
2
Selects operating mode following the order given below:
FAN (fan), COOL (cooling), DRY (dehumidying), HEAT (heating), AUTO
(automatic operation)
3
Sets the required temperature between 18°C and 30°C. The temperature
14
is increased or decreased by pressing
4
Selects the fan speed, following the order given below: AUTO (automatic),
HIGH (high), MED (medium), LOW (low)
5
Activates the SLEEP function. This function automatically adjusts the
temperature in order to provide maximum comfort during the nighttime hours
and saves energy.
6
Selects the current time on the remote control display.
7
Increases the hours on the display
8
Increases the minutes on the display
9
Sets timed switching on
10 Sets timed switching off
11 Confirms the settings to the appliance.
12 Activates or deactivates louvre movement.
13 Adjusts the louvres in order to direct the airflow in the best direction
The unit gives a beep to confirm that it has received each button command correctly.
Battery replacement
When:
- no beep of confirmation is received from the unit;
- the liquid crystal display is not working.
How:
- Pull the cover downwards as shown in the drawing to the side (2 Type AAA
1.5V batteries).
- Insert new batteries paying attention to the + and - symbols.
N.B.: Only use new batteries. Remove the batteries from the remote control
when the water cassette is not used.
s e r i e s
CSVN
HCVN
Fig. 30
13
12
10
5
4
3
and
respectively.
_
+
1,5 V
1,5 V
Fig. 31
>>
INSTALLATION, USE AND
MAINTENANCE GUIDE
I.R. REMOTE CONTROL OPERATIONS
FAN When the MODE button is pressed and the FAN mode is selected, the
cassette will operate as an electrical fan only
COOLING When the MODE button is pressed and COOL is selected, the
cassette cools the room and at the same time reduces the humidity in the air.
To start the cooling cycle, use the TEMP buttons
which is lower than the room temperature. For example: if there is a temperature
of 28°C in the room, a temperature lower than 27°C should be set in order for
the cooling to start. The appliance automatically adjusts operating cycles in order
to keep the room at the required temperature. Upon completion of settings,
press the SEND button and listen for the beep to make sure that the appliance
has received the command.
DEHUMIDIFYING When the MODE button is pressed and the DRY mode
selected, the cassette alternates cooling and fan cycles. This mode is used to
dehumidify the air without excessively altering the room temperature.
Operation is fully automatic: the appliance itself controls the fan speed.
HEATING When the MODE button is pressed and the HEAT mode is selected,
the cassette will heat the room. To start the heating cycle, use the TEMP buttons
and
to set a temperature which is higher than the room temperature. For
example: if there is a temperature of 18°C in the room, a temperature higher
than 19°C should be set in order for the heating to start. Upon completion of
settings, press the SEND button and listen for the beep to make sure that the
appliance has received the command.
AUTOMATIC OPERATION Access this mode by pressing the MODE button. In
the AUTO mode the electronic control automatically selects the operating mode
according to the room temperature (measured by the built-in sensor):
- if the room temperature drops below 18°C, the appliance will start the heating
cycle. This will continue until the temperature rises to above 20°C;
Fig. 32
and
to set a temperature
Fig. 33
Fig. 34
Fig. 35