(psi/bar)
27667203-18
300/20
27667203-28
300/20
2766 for air wall & ceiling
27667204-31
140/10
27667204-21
140/10
27667155-31
140/10
27667155-21
140/10
Safety Precautions
Safety Precautions
General Safety Rules
GENERAL SAFETY RULES
WARNING: Read and understand all instructions.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions or situations that could occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
Hose Reel Safety Precautions
1. Use proper eye protection when assembling and using the hose reel.
2. Keep children away from the work area.
3. Personal injury and/or equipment damage may result if proper safety precautions are not
observed.
4. Ensure that reel is properly installed before connecting input and output hoses.
5. Bleed fluid/gas pressure from system before servicing reel.
6. Before connecting reel to supply line ensure that pressure does not exceed maximum
working pressure rating of reel.
7. Remember, even low pressure is very dangerous and can cause personal injury or death.
8. If a leak occurs in the hose or reel, remove system pressure immediately.
9. Ensure that reel, hose, and equipment being service are properly grounded.
2766 for water wall
10. If reel ceases to unwind or rewind, remove system pressure immediately.
11. o not pull or jerk on hose.
Installation of Hose Reel
You will need to purchase appropriate hardware for mounting your new reel.
1) For mounting: For air series, Install reel on the wall and ceiling at most 9feet / 3m above the
floor. For water series, Install reel on the wall at most 4.5feet / 1.5m above the floor .
2) The reel base has two mounting holes for mounting on a suitable flat surface for air series
(four mounting holes for water series). Below figures is a template showing the correct
location of the mounting holes in the base.
3) Using the mounting holes in the base, mount the reel in the desired location. Be sure to use
appropriate hardware and tighten securely.
4) The end of incoming hose can be connected to desired supply source.
5) Outlet fittings on reel hose attach to desired tool, or nozzle. Check connection for leakage,
also check hose reel for correct operation. See: Operation section.
6) If hose stopper adjustment is required, pull hose from reel and allow to latch at desired
length. Loosen stopper bolts, and slide stopper to a position close to the hose guide. Tighten
Plastic Spring Driven Reel 2766 Series Instruction
stopper bolts, and unlatch the reel.
HR40029 for air and water - wall and ceiling mount
2766 for air wall & ceiling
2766 for water wall
NSW
QLD/PNG
TEL: (02) 9677 1555
TEL: (07) 3204 9166
FAX: (02) 9675 1155
FAX: (07) 3204 1224
Visit our website at
Work Tem.(˚C)
Air
PVC
-20～60
Air
PVC
-20～60
Water
PVC
0～60
HR40040 Instruction
PVC
Water
0～60
Water
PVC
0～60
Water
PVC
0～60
1 OF 4
2 OF 4
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
www.alemlube.com.au
(inch/mm)
(m/ft)
3/8" /10
20/65
3/8" /10
20/65
1/2" /12
20/65
1/2" /12
20/65
5/8" /15
15/50
5/8" /15
15/50
WA
SA/NT
TEL: (08) 9302 4199
TEL: (08) 8241 7111
FAX: (08) 9303 2095
FAX: (08) 8241 7011
or
www.alemlube.co.nz
Operation
1. Check reel for correct opera
2. To latch the reel, pull out th
stops retracting.
3. To unlatch the reel, slowly p
until the hose stopper rests
Note: To avoid damage to t
4. Periodically check the hose
for leakage. Replace any wo
Maintenance
Make sure the hose is in prop
Clean the hose with a cloth di
correct rewinding.
Do not use detergents or solv
Dismantling of the unit by uns
concern the preloaded spring
Limited Warranty
1. The manufacturer warrante
for a period of 24 months fr
2. Manufacturer's liability is lim
warranty period, when retur
service depot.
3. The warranty does not cove
4. The reel must be installed a
Plastic Spring
Operation
1. Check reel for correct opera
2. To latch the reel, pull out th
stops retracting.
3. To unlatch the reel, slowly p
until the hose stopper rests
Note: To avoid damage to t
4. Periodically check the hose
for leakage. Replace any wo
Maintenance
Make sure the hose is in prop
Clean the hose with a cloth di
correct rewinding.
Do not use detergents or solv
Dismantling of the unit by uns
concern the preloaded spring
Limited Warranty
1. The manufacturer warrante
for a period of 24 months fr
2. Manufacturer's liability is lim
warranty period, when retur
service depot.
3. The warranty does not cove
4. The reel must be installed a
NZ
TEL: (64) 9 447 1007
FAX: (64) 9 447 1008
2
Imprimer la page