Atlas CP400 Manuel du propriétaire - Page 10
Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Atlas CP400. Atlas CP400 16 pages. Commercial dual channel power amplifiers
Également pour Atlas CP400 : Manuel du propriétaire (16 pages), Brochure & Specs (10 pages), Manuel du propriétaire (16 pages)
Imprimer la page
CP400 & CP700 COMMERCIAL
POWER AMPLIFIER
Bridge Mono Configuration (Direct Coupled)
If higher power levels are required, the Atlas amplifier can be used in Bridge Mono mode, which utilizes
both channels of the amp across the speaker load.
CH-1
AUDIO TRANSFORMER
With the amplifier turned OFF, move the rear mounted selector switch to the "Bridge" position and connect
+
-
0
70
100
I S O L . O U T P U T
the input signal to channel one. Connect your speaker load (4 and 8 Ω only) across the "+" terminals of
both channels, with channel 1 being positive and channel 2 being negative (Figure 7).
-
+
-
+
+
70V
25V
BRIDGE
MONO
- 100V +
CH-2
CAuTION: A high voltage potential exists across the two "+" speaker terminals when operating in
AUDIO TRANSFORMER
+
-
0
70
100
I S O L . O U T P U T
any Bridge Mode application!
-
+
-
+
-
70V
25V
BRIDGE
MONO
- 100V +
MADE IN CHINA
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
To loudspeakers,
4 Ω minimum
25V, 70.7V, and 100V Transformer Output Wiring
For transformer coupled operation into high impedance loads, connect your loudspeaker leads to the
barrier strip connections labeled "Audio Transformer." Connect the speaker home runs as follows:
• 25V - Connect the positive speaker lead to the terminal labeled "100" and the negative speaker
lead to the terminal labeled "70" (Figure 8).
• 70.7V - Connect the positive speaker lead to the terminal labeled "70" and the negative speaker
lead to the terminal labeled "0" (Figure 9).
• 100V - Connect the positive speaker lead to the terminal labeled "100" and the negative speaker
lead to the terminal labeled "0" (Figure 10).
Note: Refer to page 6 of this manual to the paragraph entitled "Calculating Constant Voltage Loads" to
determine how many transformer coupled loudspeakers you can drive with the Atlas amplifier.
©2008 ATLAS SOUND LP
CH-1
CP700
D I R . O U T P U T
Commercial
Power
Amplifier
Per Channel
Output Power
400 W / 4 Ohms
350 W / 70.7 V
CH-2
D I R . O U T P U T
AC100V-50/60Hz
AC120V-50/60Hz
AC230V-50/60Hz
AC240V-50/60Hz
POWER
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. •
Printed in U.S.A.
AUDIO TRANSFORMER
8, 4, and 2 Ohms
GND
+
-
0
70
-
+
-
+
70V
BRIDGE
MONO
- 100V +
8, 4, and 2 Ohms
AUDIO TRANSFORMER
+
-
0
70
-
+
-
-
70V
BRIDGE
MONO
- 100V +
RISK OF ELECTRIC SHOCK
AVIS RISQUE DE CHOC ELECTRIQUE
Specifications are subject to change without notice
AtlasSound.com
OWNER'S MANUAL
IN
AMPLIFIER INPUTS
CH-2
+
-
GND
THRU
CH-1
LEVEL
100
I S O L . O U T P U T
1601 Jack McKay Blvd., Ennis, TX 75119
(800) 876-3333 AtlasSound.com
+
25V
CH-2
100
I S O L . O U T P U T
+
25V
MADE IN CHINA
CAUTION
DO NOT OPEN
NE PAS OUVRIR
TELEPHONE: (800) 876-3333 • FAX: (800) 765-3435
ATS002102 RevD 2/08
IN
CH-1
-
+
THRU
LEVEL
STEREO
PARALLEL
BRIDGE
Switch set
to "Bridge"
Figure 7
PP
10