3onedata IPS7110-2GC-8POE Manuel de l'utilisateur - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} 3onedata IPS7110-2GC-8POE. 3onedata IPS7110-2GC-8POE 4 pages. Ips7110 series industrial poe switch

Imprimer la page

3onedata IPS7110-2GC-8POE Manuel de l'utilisateur

Relay alarm indicator

System running indicator

10. PoE port Link/ACT indicator

11. 10/100M Base-T(x) PoE port

12. Ethernet port Link/ACT indicator

13. Gigabit SFP port of the combo port

14. Gigabit copper port of the combo port

15. 10/100M Base-T(x) port

【Dimension】

The series of products size is same, and the type of the Ethernet

interface is different. Unit (mm)

【Power supply input】

The product top panel provided 4 bit power supply input terminal

block, support DC input. DC power supply input supported

redundancy function, provided PWR1 and PWR2 power input,

can use for single, and can connect 2 separately power supply

system, use 1 pair terminal block connect the device at the same

time. If one of the power systems broke, the device can work

un-interruptible.

Built-in

overcorrect

connection protection. Voltage input range is 48VDC (terminal

block defined as: V1-、V1+、V2-、V2+). The power supports

reverse connection protection.

【Relay connection】

Relay access terminals in the top panel of the device. Between the

two terminal relay, as an open circuit state in normal non alarm

state, when there is power alarm information to the closed state.

The two terminal block connector are used to detect power failure

and network anomaly. The two wires attached to the Fault

contacts form a closed circuit when the device port connection

disconnect or has lost power supply from one of the DC power

inputs. The user can connect the relay to the lamp indicate or

buzzer alarm to remind the relevant staff.

【Console port】

This series product provided 1pcs procedure test port based in

serial port. It adopts RJ45 interface, located in top panel, can

configure related command through RJ45 to DB9 female cable.

【DIP Switch】

Top panel provided 4 bits DIP switch to do function configure

(ON to enable effective), 1 is data upgrade testing (8POE) /

reserved (4POE). 2 is recovery default factory. 3 is for upgrade. 4

is reserved. Please power off and power on when you change the

status of DIP switch.

- 2 -

【Communication connector】

protection,

Reverse

10/100/1000BaseT(X) Ethernet port

The pinout of RJ45 port display as below, connect by UTP or STP.

The connect distance is no more than 100m. 1000Mbps is used

120Ω of UTP 5e; 100Mbps is used 120Ω of UTP 5; 10Mbps is

used 120Ω of UTP 3, 4, 5.

RJ 45 port support automatic MDI/MDI-X operation. That can

connect the PC, Server, Converter and HUB. Pin 1, 2, 3, 4, 5, 6, 7,

8 Corresponding connections in MDI. 1→3, 2→6, 3→1, 4→7,

5→8, 6→2, 7→4, 8→5, are used as cross wiring in the MDI-X

port of Converter and HUB. In MDI/MDI-X, 100/1000Base-TX

PIN defines is as follows:

Note: 10Base-T/100Base-TX, "TX±"transmit data±, "RX±"receive data±,

"—"not use.

10/100Base-T(X) MDI (straight-through cable)

MDI

MDI-X

BI_DA+/TX+

BI_DB+/RX+

BI_DA-/TX-

BI_DB-/RX-

BI_DB+/RX+

BI_DA+/TX+

BI_DC+/—

BI_DD+/—

BI_DC-/—

BI_DD-/—