AutomationDirect SL4824-RR-D Manuel de démarrage rapide

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} AutomationDirect SL4824-RR-D. AutomationDirect SL4824-RR-D 4 pages.

Imprimer la page

AutomationDirect SL4824-RR-D Manuel de démarrage rapide

SOLO

Quick Start Guide

SOLO Temperature Controller

SL4824 Series

2012-01-12

5011661606-S426

This Quick Start Guide provides basic information on setting up the SOLO temperature controller. For

advanced setup and communication control as well as free configuration software visit the

AutomationDirect web site at www.AutomationDirect.com.

Product Support and Configuration Software

• For product support, specifications, and installation troubleshooting, a complete

User Manual can be downloaded from the On-line Documentation area of the

utomationDirect web site.

• For additional technical support and questions, call our Technical Support team

@ 1-800-633-0405 or 770-844-4200.

• Configuration software for the SOLO controller is available for free down-

load at www. utomationDirect.com. The software allows communication

and programming for up to four controllers at the same time. Parameters,

process values, set points and temperature changes can be monitored with

the software. The setup data can be uploaded to the user's PC via RS-485

communication. The user can monitor the temperature changes of the

controllers from the "PV Monitor" Display.

Safety Information

WARNING: To minimize the risk of potential safety problems, you should follow all applicable local and

national codes that regulate the installation and operation of your equipment. These codes vary from area to

area and it is your responsibility to determine which codes should be followed, and to verify that the equip-

ment, installation, and operation are in compliance with the latest revision of these codes.

Equipment damage or serious injury to personnel can result from the failure to follow all applicable codes and

standards. We do not guarantee the products described in this publication are suitable for your particular appli-

cation, nor do we assume any responsibility for your product design, installation, or operation.

If you have any questions concerning the installation or operation of this equipment, or if you need additional

information, please call us at 1-800-633-0405 or 770-844-4200.

This publication is based on information that was available at the time it was printed. At

Automationdirect.com® we constantly strive to improve our products and services, so we reserve the right

to make changes to the products and/or publications at any time without notice and without obligation. This

publication may also discuss features that may not be available in certain revisions of the product.

WARNING! Electric shock danger

1. To prevent electric shock, do not touch the AC terminals while the power is supplied to the controller.

This controller is an open-type temperature controller. Make sure to evaluate any dangerous application in

which a serious human injury or serious property damage may occur.

1. Always use recommended solder-less terminals: Fork terminal with insolation (M3 screw, width is 7.0mm, hole

diameter 3.2mm). Screw size: M3 x 6.5 (With 6.8 x 6.8 square washer). Recommended tightening torque: 0.4 Nm

(4kgfcm). Applicable wire: Solid/twisted wire of 2 mm, 12AWG to 24AWG. Choose AutomationDirect part numbers

BM-00120, BM-00220 or BM-00320 depending on wire size. Be sure to tighten them properly.

2. Protect the controller from dust or foreign objects to prevent controller malfunction.

3. Do not modify or disassemble the controller.

4. Do not connect anything to the "Not used" terminals.

5. Make sure all wires are connected correctly.

6. Do not install and/or use the controller in places subject to: (a) Dust or corrosive gases and liquid. (b) High humidity

7. Turn power off when wiring or changing a temperature sensor.

8. Be sure to use wires that match the thermocouple types when extending or connecting the thermocouple wires.

9. Use wires with correct resistance when extending or connecting a platinum resistance thermometer (RTD).

10. Keep the wire as short as possible when wiring a platinum resistance thermometer (RTD) to the controller and

route power wires as far as possible from load wires to prevent interference and induced noise.

11. This controller is an open-type unit and must be placed in an enclosure away from high temperature, humidity,

dripping water, corrosive materials, airborne dust and electric shock or vibration.

12. Make sure power cables and signals from instruments are all installed properly before energizing the controller,

otherwise serious damage may occur.

13. To prevent electric shock, do not touch the terminals in the controller or try to repair the controller when power is

applied.

14. Use a soft, dry cloth to clean the controller. Do not use acid or alkaline liquids for cleaning.

15. This instrument is not furnished with a power switch or fuse. Therefore, if a fuse or power switch is required, install

the protection close to the instrument. Recommended fuse rating: Rated voltage 250 V, Rated current 1 A. Fuse

type: Time-lag fuse

16. Note: This controller does not provide overcurrent protection. Use of this product requires that suitable overcur-

rent protection device(s) must be added to ensure compliance with all relevant electrical standards and codes.

(Rated 250 V, 15 Amps max). A suitable disconnecting device should be provided near the controller in the end-

use installation.

All manuals and user guides at all-guides.com

3505 HUTCHINSON ROAD

CUMMING, GA 30040-5860

General Description

AutomationDirect's SOLO is a single loop dual output temperature controller that can control both heating and

cooling simultaneously. There are four types of control modes: PID, ON/OFF, Manual, and Ramp / Soak control.

Depending upon the particular model of controller, the available outputs include relay, voltage pulse, current, and

linear voltage. There are up to three alarm outputs available to allow seventeen alarm types in the initial setting

mode. SOLO can accept various types of thermocouple, RTD, or analog inputs, and has a built in RS-485

interface using Modbus slave (ASCII or RTU) communication protocol.

Other features include:

• 1/32 DIN panel size

• 2 part x 4 character 7-segment LED display for Process Value (PV): Red color, and Set Point (SV): Green color

• Auto Tuning (AT) function with PID control

• Selectable between °C and °F for thermocouple and RTD inputs

• 0 to 50 °C (32 to 122 °F) operating temperature range

• UL, CUL and CE agency approvals

Specifications

Input Power Requirements

Operation Voltage Range

Power Consumption

Memory Protection

Control Mode

Input Accuracy

Less than ± 0.2% full scale (except thermocouple R, S, & B types) Max ± 3° (thermocouple R, S, & B types)

Vibration Resistance

10 to 55 Hz, 10 m/s

Shock Resistance

Max. 300 m/s

Ambient Temperature Range

Storage Temperature Range

Altitude

Relative Humidity

RS-485 Communication

Transmission Speed

IP65: Complete protection against dust and low pressure spraying water from all directions.

IP Rating

Agency Approvals

Degree 2 - Normally, only non-conductive pollution occurs.

Pollution Degree

Temporary conductivity caused by condensation is to be expected.

Input Types

• Thermocouple*

K, J, T, E, N, R, S, B, L, U, TXK (Sampling Rate: 400 ms / per scan)

• Platinum RTD

3-wire Pt100, JPt100 (Sampling Rate: 400 ms / per scan)

• Analog

0-50 mV, 0-5V, 0-10V, 0-20 mA*, 4-20 mA* (Sampling Rate: 150 ms / per scan)

Control Output Options

• Relay (R)

• Voltage Pulse (V)

• Current (C)

DC 4-20 mA output (Load resistance: Max 600

• Linear Voltage (L)

*Note: Use only ungrounded thermocouples.

*Note: The supplied 249 ohm resistor should be installed as shown in the terminal wiring diagrams

in section 7 for current input operation.

Output Specifications

Part Number

Input Voltage

SL4824-RR

100 - 240 VAC

Relay - SPST

SL4824-VR

100 - 240 VAC

Voltage Pulse

SL4824-CR

100 - 240 VAC

Current

SL4824-LR

100 - 240 VAC

Linear Voltage

SL4824-RR-D

24 VDC

Relay - SPST

SL4824-VR-D

24 VDC

Voltage Pulse

SL4824-CR-D

24 VDC

Current

*Output #2 can be configured as control output #2 or as an alarm output

Box Contents and Unpacking Instructions

• Unpack the SOLO temperature controller from its shipping carton. Included in the carton is the temperature

controller, mounting brackets plus hardware and this Quick Start Guide.

• Inspect all equipment for completeness. If anything is missing or damaged, immediately call the

utomationDirect returns department @ 1-800-633-0405.

• Inspect the part number to ensure the model received matches the output type required.

Mounting Bracket

and Hardware

Controller and Panel Cutout Dimensions

SOLO

4824

OUT1

OUT2

ALM

SET

1.89"

0.13"

3.93"

(48.0 mm)

(3.40 mm)

(99.8 mm)

100 to 240 VAC 50 / 60 Hz or 24 VDC

85 to 264 VAC or 21.6 to 26.4 VDC

5 VA Max

EEPROM 4K bit, number of writes 100,000

PID, ON/OFF, Ramp / Soak control or Manual

for 10 min, each in X, Y and Z directions

, 3 times in each 3 axes, 6 directions

32°F to 122°F (0°C to 50°C)

-4°F to 149°F (-20°C to 65°C)

2000m or less

35% to 80% (non-condensing)

Modbus slave ASCII / RTU protocol

2400, 4800, 9600, 19.2K, 38.4K bps

(inside suitable enclosure)

UL, CUL, CE (UL file number E311366)

SPST max. resistive load 3A @ 250 VAC

DC 14V Max, output current 40mA Max

)

DC 0-10V (Load resistance Min 1K )

Output #1

Output #2 / Alarm*

Relay - SPST

SL4824 Temperature

Controller

249 ohm

resistor

SL4824

Quick Start Guide

2.56"

(Min.)

[65.0mm]

1.76"

[44.8 mm]

0.87"

+0.02

-0

[22.0 mm]

+0.6

-0

+0.02

-0

+0.6

-0