ADEMCO 5818 Instructions d'installation - Page 2

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} ADEMCO 5818. ADEMCO 5818 2 pages. Recessed transmitter. for use q.e.d. control panels only

Imprimer la page

MOUNTING

Mark

the

selected

location

for the

transmitteron

the frame

of the door

or window.

Mark

the

Iocstion

for the magnet

the

door

or window,

directfy opposite

the transmitter location.

Caution:

Before

drillina anv holes. make

sure that su;ces;ful

Go;No

transmission/reception

tests have

been conducted as called for in the

previous section.

Drill

holes

at the

locations

marked,

for the transmitter (7/8" diameter, at least 5"

deep) and magnet (1/2" diameter, at least

1-3/4 deep).

Insert

the

transmitter

and

maanet

cases

into

their

respective

h;les,

so that their ends are flush with the surface.

DO NOT hammer in place with hard blows.

If necessary,

tap gently with a rubber

mallet or wood block.

The transmitter case may be secured by

two screws via the holes in its mounting

flanges, or the flanges can be snapped

off by scoring around them first with a

sharp knife.

if necessary, either case maybe secured

with a suitable adhesive.

A closure plug is supplied to cover an empty

transmitter hole if it becomes necessary to relo-

cate the transmitter.

BATTERY

iNSTALLATION/REPLAC~MEMT

Remove

the

transmitter'a

end

cap

by inserting the fiat blade of a small screw-

driver in the cap's slot and turning slightly

counterclockwise.

Slide

the

transmitter

board

as-

sembly

out of its case, taking care not

to bend the antenna during this step or later. -

Remove

the old battery,

if replacing it.

Observe

correct

pofarity

and

insert

the fresh

battery

into the battery holder

(+ and - polarity indications are inside). See

diagram.

Slide

the

board

assembly

back

into its case, battery end first (the reed

switch end must be toward the cap).

ReDtace

the

end

cap.

Line UD the rxo-

je~ons

on the cap with _the openings at the

edge of the case,

press the cap gently

against the PC board and turn the cap (via

its slot) slightly clockwise, thus locking it in

place.

BATTERY

CAUTION:

Risk

of fire,

ex-

plosion

and

burns.

Do not

recharge,

disassemble,

heat

above

2120F

(lt)O°C)

incinerate.

Dispose

used

batteries

promptly.

Keep

away

from

children.

SPECIFICATIONS

Dimensions

(Approximate)

Transmitted

12Jl 6" (21 mm) Diameter, 4-7/&(124mm)

Long

Magnet

IL? (13mm) Diameter, 1-3/4" (45mm) Long

Battery

3V Lithium. Replace battery only with:

Panasonic CR1 23A, Duracefl DL123A, Sanyo CR1 23A, or Ademco 466.

TO THE

INSTALLER

Regular maintenance and inspection (at least annually) by the installer and frequent testing by the

user are vital to continuous satisfactory operation of any alarm system.

The installer should assume the responsibility of developing and offering a regular maintenance pro-

gram to the user, as well as acquainting the user with the proper operation and limitations of the alarm

system and its component parts. Recommendations must be included for a specific program of fre-

quent testing (at least weekly) to insure the system's operation at all times.

REFER

THE

INSTALLATION

INSTRUCTIONS

FOR

THE

RECEIVER/CONTROL

WITH

WHICH

THIS

DEVfCE

USED,

FOR

WARRANTY

INFORMATION

AND

FOR

DETAILS

REGARDING

LIMITATIONS

THE

ENTIRE

ALARM

SYSTEM.

(zmEmEl

ALARM

DEVICE

MANUFACTURING

COMPANY

A DIVISION OF PITWAY

comwxwmoN

165

Eileen

Way,

Syosset,

New

York

11791

N702Z 1/S4

Ca@#II

01994 PlllWAY

CORPORATON