Autonics BF4GP Manuel
Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Autonics BF4GP. Autonics BF4GP 8 pages. Fiber optic amplifier
Également pour Autonics BF4GP : Manuel d'instructions (8 pages), Manuel (11 pages), Manuel (7 pages)
Imprimer la page
BF4 Series
High Reliability Of Fiber Optic Amplifier For Convenient Mounting
Features
● High speed response: max. 0.5ms
● Auto sensitivity setting (button setting)/external input sensitivity setting type
● External synchronization input, mutual interference protection, self-diagnosis
● Reverse power polarity and short-circuit (overcurrent) protection circuit
● Timer function: selectable none / 40ms OFF delay timer (fixed)
(standard type, remote sensitivity setting type only)
● Automatically selectable Light ON / Dark ON
● Precise detection of small target and easy to install in the complicated place
Please read "Safety Considerations" in operation
manual before using.
Ordering Information
BF 4 R P
Specifications
Model
Light source
Power supply
Current consumption
Operation mode
Control output
Protection circuit
Response time
Sensitivity setting
Indicator
Mutual interference prevention
Self-diagnosis output
Input of stop transmission function -
External synchronization function -
Remote sensitivity setting function -
Timer function
Insulation resistance
Noise immunity
Dielectric strength
Vibration
Shock
Ambient illumination
Environ-
Ambient temperature
ment
Ambient humidity
Material
Cable
Accessory
Approval
※ 1
Weight
※ 1: The weight includes packaging. The weight in parenthesis is for unit only.
※ The temperature or humidity mentioned in Environment indicates a non freezing or condensation environment.
-
E
Standard type
BF4RP
BF4GP
BF4R
Red LED
Green LED
Red LED
(660nm)
(525nm)
(660nm)
12-24VDCᜡ ±10% (ripple P-P: max.10%)
Max. 45mA
Light ON/Dark ON switching
NPN or PNP open collector output
● Load voltage: max. 30VDCᜡ ● Load current: max. 100mA
● Residual voltage - NPN: max. 1V (load current: 100mA), max. 0.4V (load current: 16mA) / PNP: max. 2.5V
Reverse polarity protection circuit, short-circuit (overcurrent) protection circuit
Max. 0.5ms (frequency 1), max. 0.7ms (frequency 2)
Sensitivity setting button (ON/OFF)
Control output indicator (OUT): red LED,
Stability indicator (STAB): green LED (turns ON at stable light ON/OFF level)
Built-in differential frequency mode (frequency 1 (normal mode): max. 0.5ms, frequency 2: max. 0.7ms)
ON state under unstable sensing (when the target stays for 300ms in unstable level),
ON state when control output is short-circuited
● Load voltage: max. 30VDCᜡ ● Load current: max. 50mA
● Residual voltage - NPN: max. 1V (load current: 50mA), max. 0.4V (load current: 16mA) / PNP: max. 2.5V
OFF delay (40ms)
Over 20MΩ (at 500VDC megger)
±240V the square wave noise (pulse width: 1㎲) by the noise simulator
1,000VAC 50/60Hz for 1 minute
1.5mm amplitude at frequency of 10 to 55Hz (for 1 min) in each X, Y, Z direction for 2 hours
500m/s² (approx. 50G) in each X, Y, Z direction for 3 times
Sunlight: max. 11000㏓, Incandescent lamp: max. 3000㏓ (received illumination)
-10 to 50℃, storage: -20 to 70℃
35 to 85% RH, storage:35 to 85% RH
Case: heat-resistance acrylonitrile butadiene styrene, cover: polycarbonate
Ø4mm, 4-wire, 2m
(AWG22, core diameter: 0.08mm, number of cores:
60, insulator out diameter: Ø1.25mm)
Mounting bracket, bolts, nuts
Approx. 120g (approx. 65g)
Fiber Optic Amplifier
No mark
Standard type
E
External synchronization input type
R
External input sensitivity setting type
No mark
NPN open collector output
P
PNP open collector output
R
Red LED
G
Green LED
4
Series
BF
Fiber Sensor
External synchronization
input type
BF4G
BF4R-E
BF4G-E
Green LED
Red LED
Green LED
(525nm)
(660nm)
(525nm)
Built-in
Built-in (gate/trigger)
-
-
Ø4mm, 6-wire, 2m
(AWG24, core diameter: 0.08mm, number of cores:
40, insulator out diameter: Ø1mm)
(A)
Photoelectric
Sensors
(B)
Fiber
Optic
Sensors
(C)
Door/Area
Sensors
(D)
Proximity
Sensors
(E)
Pressure
Sensors
(F)
Rotary
Encoders
(G)
Connectors/
Connector Cables/
Sensor Distribution
Boxes/ Sockets
(H)
Temperature
Controllers
(I)
SSRs / Power
Controllers
External input sensitivity
(J)
Counters
setting type
BF4R-R
BF4G-R
Red LED
Green LED
(K)
(660nm)
(525nm)
Timers
(L)
Panel
Meters
(M)
Tacho /
Speed / Pulse
Meters
(N)
Display
Units
(O)
Sensor
Controllers
(P)
Switching
Mode Power
Supplies
-
(Q)
-
Stepper Motors
& Drivers
Built-in
& Controllers
OFF delay (40ms)
(R)
Graphic/
Logic
Panels
(S)
Field
Network
Devices
(T)
Software
B-33