Autopot Auto8 Manuels d'installation - Page 2

Parcourez en ligne ou téléchargez le pdf Manuels d'installation pour {nom_de_la_catégorie} Autopot Auto8. Autopot Auto8 2 pages.

Imprimer la page

Auto8 contents

• 1x Auto8 tray

• 1x metre 6mm piping

• 1x Auto8 lid

• 8x Marix disc (square)

• 1x Round blue access cover

• 8x PotSock Square

• 1x AQUAvalve

• 8x 8.5 ltr pot if (AUTO8/8.5)

• 1x AQUAvalve cover

• 8x 15 ltr pot if (AUTO8/15)

• 1x 6mm top hat grommet

Pot and Tray Dimensions

575mm

1190mm

Required Reservoir Capacity

Auto8

1x Auto8

2x Auto8

System Size

FlexiTank or

FlexiTank

FlexiTank Pro

/ Pro 100ltr

/ Pro 225ltr

Capacity

•

Pot up your plants, water through, then allow your plants to establish in the pots for a period of 7 to 10 days before

turning your system on. This will encourage a stronger and healthier root system.

•

Always raise your reservoir to a minimum of 150mm above the highest AQUAvalve and re-fill the reservoir when

there is approximately a 1/3 of the solution left - NEVER ALLOW THE RESERVOIR TO RUN EMPTY.

•

For best results, we recommend mineral fertilisers. Do not use liquid organic fertilisers, as they have a tendency to

block small pipe work.

•

Clean all substrate from the bottom and sides of the pots before placing in each tray. This will ensure your system

is clean from the start.

•

Always use free draining substrates, for example: soil/perlite, coco/perlite, soil/clay pebbles, coco/clay pebbles,

rockwool/clay pebbles.

[email protected] I www.autopot.co.uk I +44 (0)844 8581520

260mm

350mm

245mm

15 ltr

8.5 ltr

pot

195mm

Included with

(AUTO8/8.5)

(AUTO8/15)

FlexiTank and FlexiTank Pro are the only collapsible reservoirs

that AutoPot recommend for use with Auto8 Tray Systems.

A minimum 100ltr reservoir is required per unit.

4x Auto8

8x Auto8

10x Auto8

FlexiTank

/ Pro 400ltr

750ltr

1000ltr

Advice

Auto8 Setup

Put the black marix

discs into the pots

Once pots have drained

fit a PotSock Square over

the base of each pot.

Push 6mm top hat

grommet into the hole

in the Auto8 tray wall.

Thread 6mm pipe into the

tray through the grommet.

Cut 6mm pipe to

appropriate length.

Connect via 6mm

/ 16mm fittings to a

filter (not included).

Connect filter to

reservoir. Leave tap off.

Remove any slack

from 6mm pipe by

drawing excess pipe

out of the tray.

Ensure that the circular

spirit level indicates

the tray is level,

adjust if required.

Allow your plants to establish for 7-10 days before turning system on

Advice

If you require any guidance email - [email protected]

Fill pots with medium

and pot up plants.

Water through pots

and allow to drain

outside the tray.

Make sure the pots are

clean and free of debris.

Remove AQUAvalve

collar.

Push 6mm pipe through

collar and attach to

AQUAvalve nozzle.

Rescrew collar - DON'T

overturn... when you

feel it grip STOP.

Place AQUAvalve cover

over the AQUAvalve.

The AQUAvalve and

cover should be placed

directly onto the tray.

Make sure the

system is clean and

free of debris.

Place the lid on top

of the tray. Insert the

pots. Place the round

blue access cover

over the valve.