KitchenAid YKEBS208DB7 Instructions d'installation - Page 3
Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} KitchenAid YKEBS208DB7. KitchenAid YKEBS208DB7 5 pages. 30" electric built-in single and double ovens
Imprimer la page
_fcodes p ermit a ndaseparate g rounding
wireis used, i t isrecommended thata
qualified
e lectrician
determine
that the
grounding
path and wire gauge are in
accordance
with _oca_codes.
Do Not ground to a gas pipe.
Check with
a qualified
electrician
if you are
not sure oven is proper_y grounded.
Do Not have a fuse in the neutral
or
grounding
circuit.
This oven must be connected
to a grounded
metal
permanent
wiring
system.
Oven must be connected to the proper
eUectdcaU voffage and frequency as specified
on the model/serial rating plate. (The
model/serial rating plate is located on the
oven door or on the oven frame.}
[_ Models rated from 7.3 to 9.6 kW at 240
volts (5,5 to 7,2 kW at 208 volts} require a
separate @-ampere circuit. Models rated
at 7.2 kW and below at 240 volts (5.4 kW
and below at 208 volts} require a separate
30°ampere circuit.
[_ A timeodelay fuse or circuit breaker is
recommended.
[_ Connect directly to the fused disconnect
(or circuit breaker box) through flexible,
armored or non-metallic sheathed, copper
cable (with grounding wire).
[_ Flexible armored cable from appliance
should be connected directly to junction
box.
[_ Fuse both sides of the line.
[_ A U.L.-listed conduit connector must be
provided at the junction box.
[_ Do Not cut the conduit.
Wire sizes and connections must conform
with the rating of the appliance and to the
requirements of the National Electrical Code,
ANSVNFPA 70 -- latest edition _, or Canadian
Electrical Code, C22.1-1982 and C22.2 No.
01982 (or latest edition) *_ and all local codes
and ordinances.
if the house has aluminum wiring, follow the
procedure below.
a.) Connect the aluminum wiring to the
copper wire using special connectors
designed and Underwriters Laboratories°
listed for joining copper to aluminum.
Follow the electrical connector
manufacturer's recommended procedure.
b.) Aluminum/copper
connection must
conform with local codes and industry-
accepted wiring practice.
Copies
of the standards
listed
may be obtained
from:
National
Fire Protection
Association
Ratterymamh
Park
Quincy,
Massachusetts
02269
** CSA International
8501 East Pleasant
Valley
Road
Cleveland,
Ohio
44131=5575
_
Grasp oven
frame to lift
oven,
I
IB
_
power
suppBy cable
]
Remove
_
shipping
feet.
Use screws to attach
oven to cabinet.
Reattach
side
trim.
Remove
trim screws.
Remove side
trim.
_J_
Grasp oven
frame to lift
oven.
Use screws to
attach
oven to
cabinet.
[eattach
side
trim.
Remove side
trim.
Preparation
Excessive
Weight Hazard
Use two or more people to move and
install oven.
Failure to follow this instruction
can
result in back or other injury.
Important: Use both hands to remove oven
doors.
Do Not use handle or any portion of the front
frame or trim for lifting.
Before moving oven across floor, check that
oven is on shipping base or slide oven onto
cardboard or hardboard.
Do Not remove shipping feet at the front lower
corners of oven,
Do Not remove
shipping
feet.
l
m Turn power supply off. Move oven
close to final position.
, Remove and discard shipping materials,
tape and protective film from the oven.
Do Not remove shipping base or
shipping feet at the front _ower corners
of oven. The shipping feet will protect
the _ower oven trim until oven is
inserted into cabinet.
, Remove and set aside racks and other
parts from inside oven.
Remove
oven
door.
power
X
supply cable
X
Remove
shipping
feet.
Remove trim
$srews.
Remove
oven
doors,
Replace
oven
doe!
match on the
hinge
in locked
position
=
door
free
to open
and
close
latch
on the
hinge
in unlocked
position
= door
ready
for removal
Remove trim screw.
Puff trim out,
Pull top of trim
down,
m Completely open oven door. in both
back corners of the door you will see door
latches in the locked position. Rotate both
latches forward to the unlocked position.
Grasp outside edges of door with both hands.
Begin closing door, at the moment the door
stops closing, lift and puii door toward you.
Set door aside on a protective surface.
3u
Remove trim screws attaching right
and left side trim to oven. Grasp the bottom
end of trim and pull away from oven. Slide
top end of trim downward to remove trim
from oven. Take care not to scratch other
surfaces with ends of trim. Set trim and
screws aside on protected surface.
Page 2