ABB HSCXT5A-6B Manuel d'instruction - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} ABB HSCXT5A-6B. ABB HSCXT5A-6B 14 pages. Double reduction hydroil screw conveyor drive for char-lynn h, s, t and 2000 series 6b spline motors

Imprimer la page

ASSEMBLY

Place reducer on blocks so that it lays flat with the input

shaft down

Position adapter on reducer output hub so that small end

(end with 12 holes) rests on reducer. Select the 4 mounting

holes to match the shaft used (see Fig. 1).

Place adapter screws and lockwashers through adapter and

thread into reducer. Do not tighten.

Select either lip type or braided type seals and install as

follows:

Lip Type Seals – Place seal in adapter so that spring faces

out. Seal should be tapped evenly into place in the adapter

with a soft hammer, applying force only on the outer corner

of the seal. Fill cavity between lips of seal with grease. Install

seal retainer ring by tapping with a hammer. Apply grease

to adapter section of shaft (middle section). Slide shaft,

keyseated end first, into adapter and through reducer.

Note: Be extremely careful when sliding adapter section

of shaft through seal to prevent seal lips from being

damaged or rolled over.

Braided Type Seals – Flatten both seals with a soft

hammer. Place seals in adapter, one on top of the other with

joints offset from each other. Lay retaining ring loosely on

top of seals. Slide shaft, keyseated end first, into adapter

and through reducer. Take care to clear the seals with the

adapter section of the shaft. Once shaft has bottomed, seat

retainer ring by simultaneously hitting the face of the ring on

opposite sides of the shaft with two hammers.

Carefully place reducer on its side. Rotate shaft to align

keyseats in shaft and output hub and install key. Install

shaft retainer, lockwasher and bolt. Tighten bolt to torque

specified in Table 4.

Lay reducer on blocks With input shaft down and tighten

adapter bolts to torque specified in Table 4.

If waste packing is to be used, it may be installed through

access hole provided in the adapter. Waste packing, not

furnished with the screw conveyor drive, may be used as a

separate seal option or in combination with either the lip or

braided seals.

OPTIONAL ADJUSTABLE PACKING ADAPTER

ASSEMBLY

Place reducer on blocks so that it lays flat with the input

shaft down.

Position adapter on reducer output hub so that small end

(end with 12 holes) rests on reducer. Select the 4 mounting

holes to match the shaft used. See Fig. 1.

Place adapter screws and lockwashers through adapter and

thread into reducer. Do not tighten.

Install 2 screws in studs in the adapter. Use Loctite on

threads. See Fig. 2.

Flatten braided seals with a soft hammer. Place seals in

adapter, one on top of the other with joints offset from each

other. Lay retaining ring loosely on top of seals. Slide shaft,

keyseated end first, into adapter and through adjusting

flange into reducer. Take care to clear the seals with the

adapter section of the shaft. Once shaft has bottomed, seat

retainer ring by tapping with a hammer. Install adjustable

flange and secure with hex nuts provided.

Carefully place reducer on its side. Rotate shaft to align

keyseats in shaft and output hub and install key. Install shaft

retainer, lockwasher, and bolt.

Tighten bolts per Table 4.

Lay reducer on blocks with input shaft down and tighten

adapter bolts per Table 4.

Adjustable

Flange

Hex

Nut

Figure 2 - Optional Adjustable Packing Adapter

CHAR-LYNN H, S, T AND 2000 SERIES 6B SPLINE

MOTOR INSTALLATION

Consult the local Char-Lynn Motor dealer for hydraulic motor

information.

INSTALLATION

Determine the running positions of the reducer. (See Fig.

3) Note that the reducer is supplied with 7 plugs; 5 around

the sides for horizontal installations and 1 on each face for

vertical installations. These plugs must be arranged relative

to the running positions as follows:

Horizontal Installations – Install the magnetic drain plug in

the hole closest to the bottom of the reducer. Throw away

the tape that covers the filter/ventilation plug in shipment

and install plug in topmost hole. Of the 3 remaining plugs

on the sides of the reducer, the lowest one is the minimum

oil level plug.

Vertical Installations – Install the filter/ventilation plug in

the hole provided in the top face of the reducer housing. Use

the hole in the bottom face for the magnetic drain plug. Of

the 5 remaining holes on the sides of the reducer, use a plug

in the upper housing half for the minimum oil level plug.

Adjustable

Packing

Adapter

Screw

Stud

Retainer

Ring

Braided

Seals

Drive

Shaft