Air King 9635 Panduan Pengoperasian - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Kipas angin Air King 9635. Air King 9635 2 halaman. 24" / 30" oscillating i-beam mount fan

Halaman Cetak

IMPORTANT INSTRUCTIONS - OPERATING MANUAL

I-BEAM MOUNT INSTALLATION

(Figure 1 and 2)

1. Open one tube of Loctite #243 by snapping tube neck just below end cap. Be Certain to follow all warnings noted on Loctite #243 tube.

2. Apply (1) ENTIRE tube of Loctite #243 onto the first 2 threads on the end of the L-Shaped Pipe. (Figure 1 - Inset)

3. Screw Motor Mounting Adapter into L-Shaped Pipe .The Motor Mounting Adapter MUST BE screwed in at least 4 full revolutions.

Do not allow Loctite #243 to dry before joining.

4. Rotate the Motor Mounting Adapter back to desired location and tighten with the provided 1/4" set screw.

5. Locate the L-Shaped Pipe with attached Motor Mounting Adapter to the desired location on the I-Beam flange. Install the 5/16 x 2" U-Bolts

over the L-Shaped Pipe and through the Clamping Plate Holes . The flat part of the Clamping Plate fits on the I-Beam flange and the end

with the slight bend goes against the pipe. Install flat washer, lock washer and nuts. Finger tighten the nuts on the U-Bolt. (Figure 1)

6. Slide the Clamping Plate onto I-Beam flange until U-Bolts contact flange.

7. Adjust L-Shaped Pipe so forward Clamping Plate is as close to the label at the bend as possible

8. Tighten nuts on bolt so L-Shaped Pipe does not move.

CAUTION: FAN IS HEAVY AND MAY REQUIRE TWO PEOPLE TO MOUNT.

9. Attach pull string to motor speed switch, if desired.

For Oscillating Motor: Place the flat section on the Motor Mounting Adapter next to the Motor Neck. (Figure 2A)

For Non-Oscillating Motor: Slide the Motor Neck Slot over the Motor Mounting Adapter. Align the 1/2" diameter hole in the Adapter with the

1/2" diameter holes in the Motor neck Slot. (Figure 2B)

10.Insert the 1/2" X 1" Hex Bolt (3/4" head) through the Motor Neck, and the Motor Mounting Adapter. Place 1/2" diameter Split Lockwasher

then the 1/2" diameter Hex Nut (3/4" head) and tighten fully with 2 adjustable wrenches.

11.From the same side of the Motor Neck, insert one 1/4-20 X 1 5/8" Carriage Bolt through the Arc-Shaped Slot in the Motor Neck and Hole

in the Motor Mounting Adapter.

To Fasten: Place one 1/4" Flatwasher, one 1/4" Internal Tooth Lockwasher, a second 1/4" Flatwasher and then tighten the Adjustable Knob

over the remaining threads.

I-Beam

Mounting

Hardware

I-Beam Flange

Clamping

Plate

Inset

Loctite 243

U-Bolts

Application Loctite 243

Set Screw

Motor Mounting

Adapter

Motor Mounting

Hardware

Non-Oscillating Motor Shown

New 8/04

Oscillating Motor View

Motor

Mounting

Adapter

L-Shaped

Pipe

Clamping

Plate

Exploded View for Detail

Non-Oscillating Motor View

Motor

Mounting

Adapter

Exploded View for Detail

IMPORTANT INSTRUCTIONS - OPERATING MANUAL

GRILL AND BLADE ASSEMBLY

NOTE: The assembly of the blade and grill is identical, regardless if the Fan has an oscillating motor or a non-oscillating

motor. One of each is shown in the illustrations below.

1. Install the Rear Grill onto the Motor , lining up the six holes in the grill with the six threaded holes in the Motor . Install (6) 10-32 X 5/16"

Hex Screws through the Rear Grill into the Motor . Securely tighten all (6) screws. (Figure 3)

2. Push the Fan Blade onto the Motor Shaft , centering the Hub facing away from the motor, until it stops against the shaft (Inset A) . Align

Square Head Bolt with flat of the Motor Shaft . TIGHTEN VERY SECURELY WITH AN ADJUSTABLE WRENCH. Failure to securely

tighten the Bolt could result in damage to the Fan and/or personal injury.

3. Hold the Front Grill so that the name, in the center, is right side up and straight across. Starting at the top: Fasten Front Grill to Rear

Grill by sliding the hooked wires on the Front Grill over the outermost ring on the Rear Grill . (Figure 4/ Detail A) . The bottom most hooks

will require the use of a flathead screwdriver to complete assembly. Stand behind the Fan. Slip the flat of the screwdriver between the

Front and Rear Grills, next to one of the unfastened hooks. (Figure 4/ Detail B) Pull screwdriver handle upwards towards the Rear Grill.

Slip the Front Grill hook over the Rear Grill outer ring with a push. Repeat procedure with remaining hooks.

CAUTION: DO NOT BEND WIRES ON THE FRONT OR THE REAR GRILLS.

Figure 2A

Oscillating Motor Shown

CAUTION: THE SECONDARY SUPPORT CABLE PROVIDED SHOULD BE

USED ANYTIME THE CIRCULATOR IS MOUNTED OVERHEAD FOR

ADDITIONAL SAFETY.

SECONDARY SUPPORT CABLE

1. Loop one end of Cable around the Large Guard Wires of both the Front and Rear Grills.

2. Attach a Cable Clamp with the "U" on the tail side of the loop leaving a tail

approximately 1 to 2 inches. Tighten Clamp Nuts. Make sure no part of the Cable

interferes with the Blade.

3. Wrap the other end of the Cable around a secure building joist, truss, or other support near

the Fan. Take up all excess slack in the Cable.

CAUTION: USE ONLY THE MOUNTING HARDWARE WHICH

IS RECOMMENDED FOR USE ON THIS FAN.

4. Attach the remaining Cable Clamp as indicated in Step 2. The excess tail should be

Figure 2B

trimmed to extend 1 to 2 inches past the Clamp.

5. Check the Assembly to assure the Blade is free of all obstructions.

CAUTION:

Use of the secondary support cable does not guarantee protection against injury of persons, mounting of both the

circulator and cable could fail if subjected to abuse, neglect or improper installation.

OPERATING INSTRUCTIONS

1. TO OPERATE: Plug cord into a grounded 120V, 60 Hz outlet. Select desired operating speed with pull cord on the rear of the motor:

First pull: High

Second pull: Medium

Third pull: Low

Fourth pull: OFF

Failure to securely hold onto head assembly while adjusting head angle

2. TO ADJUST HEAD ANGLE: While holding head firmly, loosen knob under motor (turn counterclockwise). Tilt head to desired position

FIRMLY retighten knob under motor.

NOTE:

Motor Head Adjustment Knob and the On/Off Pull Cord have the same location on oscillating or non-oscialling models.

New 8/04

5084417

(Figures 3 and 4)

Inset A

Figure 3

Non-Oscillating Motor Shown

(Figure 5)

NOTE: THIS FAN IS VERY HEAVY.

could result in personal injury.

Detail A

Top Hooks

Detail B

Bottom Hooks

Figure 4

Large Guard

Wires

Figure 5

5084417