Air King 99533 Panduan Pengoperasian - Halaman 3
Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Kipas angin Air King 99533. Air King 99533 8 halaman. 24” & 30” quiet design oscillating pedestal fan
Halaman Cetak
COLuMn AnD MOtOR
ASSeMBLY
Locate Motor Hardware Bag to
Assemble Column and Motor Assembly.
1. Place flat section on Upper Tube of Column
Assembly next to Neck on Motor Assembly.
Align the 1/2" diameter hole in the flat section
on the Upper Tube ofColumn Assembly with
the 1/2" diameter hole in the Motor Assembly.
(Figure 1)
2. Insert the 1/2" X 1" Hex Bolt (3/4" head)
through the Motor Neck, and the Upper
Tube Assembly. Place 1/2" diameter Split
Lockwasher then the 1/2" diameter Hex Nut
(3/4" head) and tighten fully with a adjustable
wrench. (Figure 1)
3. From the same side of the Motor Neck,insert
one 1/4-20 X 1 5/8" Carriage Bolt through
the Arc-Shaped Slot in the Motor Neck and
Hole in the Upper Pipe of Column Assembly.
(Figure 1)
4. Attach pull string to motor speed switch, if
desired.
Actual motor not shown for
detailed hardware view.
New 5/11
COLuMn/MOtOR tO BASe/
1. Rest Column and Motor Assembly on floor next
to the Base Assembly. Tilt Base Assembly up on
end. Pick up lower pipe of Column Assembly and
insert into the Mounting Flange. (Figure 2)
2. Loosen (2) 3/8-16 X 3/8" Allan Head Bolt in the
Mounting Flange. This will allow the Column to
settle in the bottom of the Base after setting the
Fan upright.
3. Tilt entire assembly to the upright position.
MAKe SuRe BOLtS In COLuMn AnD
MOtOR ASSeMBLY StePS ARe tIGHt
BeFORe StAnDInG FAn uPRIGHt.
4. Tighten the (2) 3/8-16 X 3/8" Allen Head Bolt in
the Mounting Flange.
GRILL AnD BLADe ASSeMBLY
Locate remaining parts from Motor Hardware Bag
to Assemble Grills and Blade to the Motor.
1. Install the Rear Grill onto the Motor, lining up
the six holes in the grill with the six threaded
holes in the motor mounting flange. Install (6)
10-32 X 5/16" Hex Screws through the rear
grill into the grill mounting flange. Securely
tighten all (6) screws. (Figure 3)
2. Push the Fan Blade onto the Motor Shaft,
centering the Hub facing away from the
motor, until it stops against the shaft (Inset
A) . Align Square Head Bolt with flat of the
motor shaft. tIGHten VeRY SeCuReLY
WItH An ADJuStABLe WRenCH. Failure
to securely tighten the Bolt could result in
damage to the Fan and/or personal injury.
Figure 1
3. Hold the Front Grill so that the name, in the
center, is right side up and straight across.
Starting at the top: Fasten Front Grill to
Rear Grill by sliding the hooked wires on
the Front Grill over the outermost ring on
the Rear Grill. (Figure 4 / Detail A). The
bottom most hooks will require the use of a
flathead screwdriver to complete assembly.
Stand behind the Fan. Slip the flat of the
screwdriver between the Front and Rear
Grills, next to one of the unfastened hooks.
(Figure 4 / Detail B) Pull screwdriver handle
upwards towards the Rear Grill. Slip the Front
Grill hook over the Rear Grill outer ring with
a push. Repeat procedure with remaining
hooks.
CAutIOn: DO nOt BenD WIReS On tHe
FROnt OR tHe ReAR GRILLS.
ASSeMBLY
Figure 2
3
GRILL AnD BLADe ASSeMBLY
COntInueD
Figure 3
Detail A
Detail B
Inset A
Figure 4
5085460