Air King 8365 Petunjuk Penting & Panduan Pengoperasian - Halaman 4
Jelajahi secara online atau unduh pdf Petunjuk Penting & Panduan Pengoperasian untuk Pemanas Air King 8365. Air King 8365 8 halaman. 30" digital ceramic pedestal heater with remote
Halaman CetakMODEL 1DKX5/8365
DESCRIPTION
®
The Air King
Oscillating Ceramic Heater features 2 heat settings.
The heater oscillates 45° and features a 6ft. (1.82m) 16/3 grounded
cordset.
SPECIFICATIONS
Motor..................................120 V/60 Hz
Control................................Manual/Remote
Settings...............................High and Low Heat
Air Flow Distribution............45˚
Approvals............................ETL listed. Close mesh
blower guard meets OSHA requirements.
OPERATION
The Heater may be operated by the manual controls located
on the Heater (as shown in Figure 1) or by your remote control
(shown in Figure 2).
1. Place the Heater on a firm, level surface, after assembling per this
manual.
CAUTION: Plastic or rubber tabs, like the feet on this unit, may stick
to furniture surfaces and/or hardwood floors. The unit may leave a
residue that could darken, stain or leave permanent blemishes on
the finish of certain furniture surfaces, including wood surfaces,
and/or hardwood floors.
2. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may
slip partially or completely out of the receptacle
with only the slight movement of the attached cord.
Receptacles in this condition may overheat and pose
a serious fire hazard; if covered by a curtain or drape,
the fire hazard is even greater.
3. When the Heater is initially plugged in, there will be a 'beep' and
the power light will come on indicating that there is power to the
unit. The power light will remain lit until the Heater is unplugged
from the electrical outlet.
4. Turn the Heater ON by pressing the Power Button ( ).
5. When initially turned on, the Heater will display the current
room temperature in ° Fahrenheit. Press the ( ) and ( ) but-
tons at the same time to change the display to ° Celsius. Press
the same two buttons together again to change the display back
to ° Fahrenheit.
6. The display will reflect the current room temperature (Display
will read "Room Temp") The unit will be in the HIGH heat. (1500
Watts)
7. Pressing the ( ) Button at this point will set the Heater into LOW heat.
8. To turn the Heater OFF, press the Power Button ( ) and unplug
the unit from the electrical outlet.
View of Control Panel
Figure 1
Rev. D 5/09
MODEL
1DKX5/8365
SETTINGS HIGH
LOW
BTU
5118
3070
Amps
12.5
7.0
Watts
1500
900
dB A
47
<40
OSCILLATION FUNCTION
Pressing the Oscillation Button ( ) will allow the Heater to oscil-
late back and forth. To stop the oscillation, press the Oscillation
Button ( ) again. When the Heater is in Automatic Temperature
Control, the oscillation function will stop when the set temperature
is reached and resume when the Heater turns back on.
TIMER FUNCTION
The timer function will work in any mode. The timer function allows
you to set the length of operation from 1 hour to 8 hours. Pressing
the Timer Button ( ) will increase the length of operation by 1 hour
each time the button is pressed. Pressing the Timer Button ( )
once more after the display reflects 8 hours will reset the Heater
to continuously running. Once the timer has been set, the timer
will count down the hours in 1 hour increments, showing on the
display the remaining operating time. The Heater will turn itself
off when the set time has lapsed. The unit can be turned back on
by pressing the Power Button ( ).
THERMOSTAT INSTRUCTIONS
1. Pressing the ( ) or ( ) Button will prompt the Heater into High
heat and will allow the thermostat to be set at a desired tem-
perature. The display will show AUTO and the word "SET". The
temperature will be flashing.
2. To adjust SET temperature, press the ( ) to increase the desired
temperature and the ( ) to decrease the desired temperature.
3. When the air temperature reaches 2 degrees above the SET
temperature, the heater will shut off.
4. When the air temperature drops 1 degree below the SET
temperature, the unit will come back on.
NOTE: It is normal for the Heater "fan" to run for approximately 15 sec-
onds after the Heater shuts off after reaching the set temperature.
REMOTE CONTROL
(Figure 2)
All the functions performed with the Remote Control work identi-
cally to the manual controls, except that you are unable to change
from °F to °C with the remote control.
1. Install the two "AAA" batteries supplied.
2. Do not mix old and new batteries. Do not mix alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium) batteries.
3. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY
EXPLODE OR LEAK.
Front View of
Rear View of
Remote Control
Remote Control
(
) = More Heat
�
(
) = Less Heat
( ) = Power
(
) = Oscillation
�
(
) = High / Low Setting
(
) = Timer
Figure 2
4
ASSEMBLAGE
(Figures 1 à 6)
OUTILS REQUIS: Tournevis phillips #2 (non compris)
Retirez soigneusement la chaufferette de sa boîte et du sac. Pour
faciliter l'assemblage, déposer la chaufferette de sorte que la grille
avant et le panneau de conrôle font face vers le haut.
(8) - M5 X 13mm
(2) - M4 X 13mm
Les vis sont montrées en taille réelle
1. Localiser le cordon d'alimentation électrique au bas de la
chaufferette. Passer le cordon d'alimentation électrique par le
centre de l'assemblage de support de colonne.
2. Fixer l'assemblage de support de colonne à la base du moteur
avec (4) vis M5 X 13 mm. Assurez vous d'aligner la clé sur la base
de moteur avec l'encoche de localisation sur l'assemblage de
support de colonne. (Figure 2)
Cordon
d'alimentation
électrique
support de colonne
3. Assembler la base en entre barrant les bosses dans les trous
des bosses. (Figure 3)
Bosses
Clé
8365ESF
Rev. D 5/09
MODÉLE 1DKX5/8365
4. Fixer les moitiés de la base avec (2) vis M4 X 13mm. Passer
le cordon d'alimentation électrique par le gros trou dans
l'assemblage de la base. REMARQUE: La voie d'accès
du cordon au bas de la base doit être vers l'arriére de la
chaufferette. (Figure 4)
Voie d'accés
du cordon
L'assemblage
de la base
Figure 1
5. Aligner l'assemblage de la base avec l'assemblage de support
de colonne. Assurez-vous d'aligner l'encoche de localisation
sur l'assemblage de support de colonne avec la clé sur
Base du
l'assemblage de la base (Figure 5). Fixer l'assemblage de la
moteur
base à l'assemblage de support de colonne avec les (4) vis
M5 X 13mm. Tirer délicatement tout excès lâche de cordon
d'alimentation électrique et le placer dans la voie d'accés du
cordon de l'assemblage de la base. (Figure 6)
Clé
Assemblage de
Figure 2
Clé
L'assemblage
de la base
Trous des
bosses
Voie d'accès du
Figure 3
13
Cordon
d'alimentation
électrique
Figure 4
Encoche de
localisation
Figure 5
L'assemblage
de support de
colonne
Cordon
d'alimentation
électrique
cordon
Figure 6
8365ESF