Electrolux ARTHUR MARTIN ACN3058 Panduan Pengoperasian dan Instalasi - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pengoperasian dan Instalasi untuk Pembeku Electrolux ARTHUR MARTIN ACN3058. Electrolux ARTHUR MARTIN ACN3058 6 halaman. Chest freezer

Halaman Cetak

G G B B

WHEN NOT IN USE

Disconnect the appliance from the electricity supply. Remove all goods from the freezer. Clean the freezer as described above. Leave

the lid slightly open. If you are still unable to solve the problem, summon the assistance of authorised service staff. Do not take any

other steps. Incorrect procedure may cause personal injury or lead to additional defects. It is quite normal for the freezer to seem warm

on the outside occasionally, owing to the heat generated by the freezing process. This heat also helps to prevent the formation of mois-

ture on the outside of the appliance which could cause rust. If the freezer has been switched off briefly, the compressor may not start

immediately when the current is re-connected. This is quite normal.

IF YOUR FREEZER DOES NOT FUNCTION SATISFACTORILY

Check the following before calling for service staff:

Defect:

Check if:

Freezer not

Green light not on

cold enough

Green and red light on

Green light on, red

light not on

Yellow light on

Freezer too

cold

Yellow light not on

Too much

Lid does not close

frost

completely

formed

Lot of moisture in the

room

Goods packed poorly

If you are still unable to solve the problem, summon the assistance of authorised service staff. Do not take any other steps. Incorrect

procedure may cause personal injury or lead to additional defects. It is quite normal for the freezer to seem warm on the outside occa-

sionally, owing to the heat generated by the freezing process. This heat also helps to prevent the formation of moisture on the outside

of the appliance which could cause rust. If the freezer has been switched off briefly, the compressor may not start immediately when

the current is re-connected. This is quite normal.

HOW TO CHANGE THE BULB

Before changing the bulb, isolate the appliance from the electricity supply. Exert pressure to remove

the light glass as shown in the drawing. Unscrew the bulb, and replace it with a new bulb (max. 15W).

Then re-connect the electricity supply. Extra bulbs are available from your local Electrolux Service

Centre.

PREPARATION OF ICE CUBE MAKER

1.Fill the ice cube maker until the cubes will be full in the horizontal position or by the

load line mark in the vertical position. After this close the ice cube maker with cap.

2.Place the holder in the lid of the freezer and leave to solidify

3.To loosen the frozen cubes, either bend the ice cube tray or hold it under running

water for a few seconds.

Important! Never try to free an ice tray that is frozen to the freezer compartment

using pointed or sharp edged objects. Use a soft plastic scraper.

ACCESSORIES

Spare baskets can be obtained from your local Service Centre. The

illustrations on this page show how many baskets can be placed in the

various freezer models.Measure the length of your freezer and find the

appropriate illustration. The number above each illustration indicates its

length in millimetres.

Possible cause:

Plug not connected correctly

Defect in switch or fuse

Power failure

Fresh food recently placed in freezer

Lid open too long

Thermostat set too warm

Lot of frost and ice formed

"Super" function active

Thermostat set too cold

Lid in contact with goods in free-

zer

Moisture from washing machine,

tumble-dryer, etc.

Lot of moisture from goods

Action:

Check plug and socket

Check fuse, call electrician

Wait until current returns

Wait a couple of hours

Set thermostat colder

Defrost freezer

Press "Super" button out

Set thermostat warmer

Re-arrange goods, check that lid

closes correctly

Move freezer to a room with less

moisture, or air regularly

Re-pack goods, see under

"How to use"

Cup of the ice cube maker

Load line

Load line of the ice cube maker